User manual GIGABYTE GA-8I915P-D PRO

[. . . ] GA-8I915P-D Pro Intel® Pentium® 4 LGA775 Processor Motherboard User's Manual Rev. 2003 12ME-8I915PDP-2003 Motherboard GA-8I915P-D Pro Motherboard GA-8I915P-D Pro Jun. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without Gigabyte's prior written permission. [. . . ] for automatic sy stem restart or clear the CMOS setup data and perform a safe restart. (Default v alue) Enabled Enable CPU Host Clock Control. CPU Host Frequency (Mhz) This item w ill be av ailable w hen "CPU Host Clock Control" is set to Enabled. If y ou use FSB800 Pentium 4 processor, please set "CPU Host Frequency " to 200MHz. For pow er End-User use only ! Memory Frequency For Wrong frequency may make sy stem can't boot, clear CMOS to overcome wrong frequency is sue. for FSB(Front Side Bus) frequency =533MHz, 2. 5 Memory Frequency = Host clock X 2. 5. (Default v alue) for FSB(Front Side Bus) frequency =800MHz, 1. 66 Memory Frequency = Host clock X 1. 66. (Default v alue) Mem ory Frequency (Mhz) The values depend on "Memory Frequency For" item. DIMM O verVoltage Control Please note that by ov erclocking y our sy stem through the increase of the DIMM v oltage, damage to the memory may occur. For pow er End-User use only ! PCI-E O verVoltage Control Normal +0. 1V +0. 2V +0. 3V Set PCI-E Ov erVoltage Control to Normal. Set PCI-E Ov erVoltage Control to +0. 3V. CPU Voltage Control Supports adjustable CPU Vcore from 0. 8375V to 1. 6000V. (Default v alue: Normal) Warning: CPU may be damaged or reduce CPU life-cy cle w hen CPU is ov er-v oltage. Normal CPU Vcore Display y our CPU Vcore Voltage. (Note) To use a DDRII 600 memory module on the motherboard, y ou must install an 800MHz FSB processor and set Memory Frequency For to 3. 00. - 44 - GA-8I915P-D Pro Motherboard 2-8 } } } } } } } Select Language CMOS Setup Utility -Cop y right (C) 198 4-2004 Award Software Stan dard CM OS Features Advanc ed BIOS Fe atures IntegratedPeripherals Power Manag ement Setup PnP/PCI Configur ations PC H ealth Status MB In telligent Tweaker(M. I. T. ) Select L anguage Load Fail-Safe Defaults Load Optimized Defaults Set Su pervisor Pa ssword Set User Password Save & Exit Setup Exit Without Saving F3: Change Lan guage F10: Save & Exit Setup English ESC: Qu it F8: Du al BIOS/Q- Flash Multi-language supports 7 languages. There are English, French, German, Spanish, Traditional Chinese, Simplified Chinese and Japanese. 2-9 } } } } } } } Load Fail-Safe Defaults CMOS Setup Utility -Cop y right (C) 198 4-2004 Award Software Stan dard CM OS Features Select L anguage Advanc ed BIOS Fe atures Load Fail-Safe Defaults IntegratedPeripherals Load Optimized Defaults Power Manag ement Setup Set Su pervisor Pa ssword Load Fail-Safe D efaultsSet UserN (Y/N)?Password PnP/PCI Configur ations PC H ealth Status Save & Exit Setup MB In telligent Tweaker(M. I. T. ) Exit Without Saving F3: Change Lan guage F10: Save & Exit Setup Load Fail-Safe Defaults ESC: Qu it F8: Du al BIOS/Q- Flash Fail-Safe defaults contain the most appropriate v alues of the sy stem parameters that allow minimum sy stem performance. - 45 - BIOS Setup English 2-10 Load Optimized Defaults CMOS Setup Utility -Cop y right (C) 198 4-2004 Award Software } } } } } } } Stan dard CM OS Features Select L anguage Advanc ed BIOS Fe atures Load Fail-Safe Defaults IntegratedPeripherals Load Optimized Defaults Power Manag ement Setup Set Su pervisor Pa ssword Load Optimized D efaults (Y/N)?N PnP/PCI Configur ations Set User Password PC H ealth Status Save & Exit Setup MB In telligent Tweaker(M. I. T. ) Exit Without Saving F3: Change Lan guage F10: Save & Exit Setup Load Optimized Defaults ESC: Qu it F8: Du al BIOS/Q- Flash Selecting this field loads the factory defaults for BIOS and Chipset Features w hich the sy stem automatically detects. 2-11 Set Supervisor/User Password CMOS Setup Utility -Cop y right (C) 198 4-2004 Award Software } } } } } } } Stan dard CM OS Features Advanc ed BIOS Fe atures IntegratedPeripherals Power Manag ement Setup PnP/PCI Configur ations Enter Pa ssword: PC H ealth Status MB In telligent Tweaker(M. I. T. ) Select L anguage Load Fail-Safe Defaults Load Optimized Defaults Set Su pervisor Pa ssword Set User Password Save & Exit Setup Exit Without Saving F3: Change Lan guage F10: Save & Exit Setup Change/Set/Dis able Password ESC: Qu it F8: Du al BIOS/Q- Flash Selecting this field loads the factory defaults for BIOS and Chipset Features w hich the sy stem automatically detects. When y ou select this function, the follow ing message will appear at the center of the screen to assist y ou in creating a passw ord. You may also press <Esc> to abort the selection and not enter a passw ord. To disable passw ord, just press <Enter> w hen y ou are prompted to enter passw ord. [. . . ] Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address (English): http://www. gigabyte. com. tw WEB address (Chinese): http://chinese. giga-byte. com -- U. S. A. Support : http://www. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. giga-byte. com -- Germany G. B. T. TECHNOLOGY TRADING GMBH Address: Friedrich-Ebert-Damm 112 22047 Hamburg TEL: +49-40-2533040 (Sales) +49-1803-428468 (Tech. ) FAX: +49-40-25492343 (Sales) +49-1803-428329 (Tech. ) Tech. [. . . ]