User manual GIGABYTE GA-8GEM667

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] IDE1 Conductor Cable !Auto !ATA66/100 !ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). !IDE2 Conductor Cable !Auto !ATA66/100 !ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). !Onboard H/W LAN (*) !Enabled !Disabled Enabled onboard H/W LAN Function. (Default value) Disabled onboard H/W LAN Function " * " Only for GA-8GEM667. GA-8GEM667 Series Motherboard - 32 - !Onboard LAN Boot ROM (*) !Enabled !Disabled Enabled onboard LAN Boot ROM. Onboard Serial Port 1 !Auto !3F8/IRQ4 !2F8/IRQ3 !3E8/IRQ4 !2E8/IRQ3 !Disabled BIOS will automatically setup the port 1 address. Onboard Serial Port 2 !Auto !3F8/IRQ4 !2F8/IRQ3 !3E8/IRQ4 !2E8/IRQ3 !Disabled BIOS will automatically setup the port 2 address. UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) !ASKIR !IrDA !Normal Set onboard I/O chip UART to ASKIR Mode. Onboard Parallel port !378/IRQ7 !278/IRQ5 !Disabled !3BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. - 33 BIOS Setup English !Parallel Port Mode !SPP !EPP !ECP !ECP+EPP Using Parallel port as Standard Parallel Port. Using Parallel port as ECP & EPP mode. !ECP Mode Use DMA !3 !1 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. !Game Port Address !201 !209 !Disabled Set Game Port Address to 201. Disable this function. !Midi Port Address !300 !330 !Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. !Midi Port IRQ !5 !10 Set Midi Port IRQ to 5. (Default Value) !CIR Port Address !310 !320 !Disabled Set CIR Port Address to 310. Disable this function. (Default Value) !CIR Port IRQ !5 !11 Set CIR Port IRQ to 5. (Default Value) GA-8GEM667 Series Motherboard - 34 - English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Power Management Setup ACPI Suspend Type Soft-Off by PWR_BTTN PME Event Wake Up ModemRingOn/WakeOnLan Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Power On By Mouse Power On By Keyboard x KB Power ON Password AC Back Function [S1(POS)] [Instant-Off] [Enabled] [Enabled] [Disabled] Everyday 000 [Disabled] [Disabled] Enter [Soft-Off] Item Help Menu Level & [S1] Set suspend type to Power On Suspend under ACPI OS [S3] Set suspend type to Suspend to RAM under ACPI OS "#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Fail-Safe Defaults Figure 5: Power Management Setup F1:General Help F7:Optimized Defaults !Soft-off by PWR_BTTN !Instant-off Press power button then Power off instantly. Modem Ring On/ WakeOnLAN (When AC Back Function is set to [Soft-Off]) M You can enable wake on LAN feature by the "ModemRingOn/WakeOnLAN" or "PME Event Wake up" when the M/B has "WOL" onboard connector. [. . . ] Cable with rear bracket is provided and could link to the "SPDIF output" connector (As picture. ) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting port. 1. Connect the SPDIF output device to the rear bracket of PC, and fix it with screw. 2. Connect co-axial or optical output to the SPDIF decoder. GA-8GEM667 Series Motherboard - 72 - English - 73 - Technical Reference English GA-8GEM667 Series Motherboard - 74 - Revision History Chapter 5 Appendix Picture below are shown in Windows XP (CD driver version 1. 0) Appendix A: Chipset Driver Installation A. Intel Chipset Software Installation Utility: Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. [. . . ]