User manual GIGABYTE GA-7VT600

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X(3. 3V) card is not supported by VIA® KT600. Please insert an AGP 4X/8X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X (1. 5V) mode by adjusting the jumper. [. . . ] If a hard disk controller card is used, set at Disabled. 8Enabled 8Disabled Enable onboard 2nd channel IDE port. (Default value) Disable onboard 2nd channel IDE port. FAC97 Audio 8Enabled 8Disabled BIOS will automatically detect onboard AC97 Audio. (Default value) Disabled AC97 Audio. FUSB 1. 1 Controller MDisable this option if you are not using the onboard USB feature. 8Enabled 8Disabled Enabled USB Controller. (Default value) Disabled USB Controller. FUSB 2. 0 Controller MDisable this option if you are not using the onboard USB 2. 0 feature. 8Enabled 8Disabled Enabled USB 2. 0 Controller. (Default value) Disabled USB 2. 0 Controller. FUSB Keyboard Support MWhen a USB keyboard is installed, please set at Enabled. 8Enabled 8Disabled Enabled USB Keyboard Support. (Default value) FUSB Mouse Support 8Enabled 8Disabled Enabled USB Mouse Support. (Default value) GA-7VT600(-L) Motherboard - 40 - FOnboard H/W LAN * 8Enabled 8Disabled Enable Onboard H/W LAN function. (Default value) Disable this function. English FOnboard LAN Boot ROM * This function decide whether to invoke the boot ROM of the onboard LAN chip. (Default Value) Enable this function. FOnboard Serial Port 1 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS will automatically setup the port 1 address. (Default value) Enable onboard Serial port 1 and address is 2F8, Using IRQ3. Disable onboard Serial port 1. FOnboard Serial Port 2 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS will automatically setup the port 2 address. (Default Value) Enable onboard Serial port 2 and address is 3E8, Using IRQ4. Disable onboard Serial port 2. FOnBoard Parallel port MThis feature allows you to select from a given set of parameters if the parallel port uses the onboard I/O controller. 8378/IRQ7 8278/IRQ5 83BC/IRQ7 8Disabled Enable onboard LPT port and address is 378, Using IRQ7. (Default Value) Enable onboard LPT port and address is 278, Using IRQ5. Disable onboard parallel port. " * " FOR GA-7VT600-L Only. - 41 - BIOS Setup . English FParallel Port Mode MThis feature allows you to connect with an advanced print via the port mode it supports. 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port using IRQ7. Using Parallel port as ECP & EPP mode. FGame Port Address 8Disabled 8201 8209 Disabled this function. (Default Value) Set Game Port Address to 209. FMidi Port Address 8Disabled 8300 8330 Disabled this function. Set Midi Port Address to 330. (Default Value) FMidi Port IRQ 85 810 Set 5 for Midi Port IRQ. Set 10 for Midi Port IRQ. (Default value) GA-7VT600(-L) Motherboard - 42 - English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type øUSB Device Wake-Up From S3 Power LED in S1 state Soft-Off by PWRBTN AC Back Function Keyboard Power On Mouse Power On PME Event Wake Up ModemRingOn/WakeOnLAN Resume by Alarm ø Date(of Month) Alarm ø Time(hh:mm:ss) Alarm [S1(POS)] Disabled [Blinking] [Instant-off] [Soft-Off] [Disabled] [Disabled] [Enabled] [Enabled] [Disabled] Everyday 0: 0: 0 Item Help Menu Levelu higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Power Management Setup - 43 - BIOS Setup English FACPI Suspend Type 8S1(POS) 8S3(STR) Set suspend type to Power On Suspend under ACPI OS(Power On Suspend). (Default value) Set suspend type to Suspend To RAM under ACPI OS (Suspend To RAM). FUSB Device Wakeup From S3(When ACPI Suspend Type is set [S3(STR)]) USB device wakeup From S3 can be set when ACPI standby state set to S3/STR. 8Enabled 8Disabled USB Device can wakeup system from S3. (Default value) FPower LED in S1 state 8Blinking 8Dual/Off In standby mode(S1), power LED will blink. If use dual color LED, power LED will turn to another color. FSoft-off by PWRBTN 8Instant-off 8Delay 4 Sec. Enter suspend if button is pressed less than 4 sec. FAC Back Function 8Memory 8Soft-Off 8Full-On System power on depends on the status before AC lost. [. . . ] Answer: Gigabyte motherboards will auto-detect the external VGA card after it is plugged in, so you don't need to change any setting manually to disable the onboard VGA. Please refer to the user manual and check whether you have connected any cable that is not provided with the motherboard package to the USB Over Current pin in the Front USB Panel. If the cable is your own cable, please remove it from this pin and do not connect any of your own cables to it. English GA-7VT600(-L) Motherboard - 78 - Question 10: Sometimes I hear different continuous beeps from computer after system boots up. Answer: The beep codes below may help you identify the possible computer problems. [. . . ]