User manual GIGABYTE GA-7S748

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X(3. 3V) card is not supported by SiS® 748. Please insert an AGP 4X/8X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X (1. 5V) mode by adjusting the jumper. [. . . ] (Default Value) Suspend The user press the pow er button once, then he can enter suspend mode. System after AC Back LastState When AC-pow er back to the sy stem, the sy stem w ill return to the Last state before AC-pow er off. Off When AC-pow er back to the sy stem, the sy stem w ill be in "Off" state. (Default Value) On When AC-pow er back to the sy stem, the sy stem w ill be in "On" state. - 41 BIOS Setup English IRQ [3-7, 9-15], NMI Disabled Enabled Disable this function. (Default v alue) ModemRingOn Disabled Enabled Disable Modem Ring on function. (Default Value) PME Event Wake Up Disabled Enabled Disable this function. (Default Value) Power On by Keyboard Passw ord Input passw ord (from 1 to 8 characters) and press Enter to set the Key board Pow er On Passw ord. (Default Value) Power On by Mouse Enabled Disabled Enable Pow er On by Mouse function. (Default Value) Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to pow er on sy stem. (Default Value) Enable alarm function to POWER ON sy stem. If RTC Alarm Lead To Pow er On is Enabled. Month Alarm : Day (of Month) : Time ( hh: mm: ss) : NA, 1~12 1~31 (0~23) : (0~59) : (0~59) Power LED i n S1 state Blinking Dual/OFF In standby mode(S1), pow er LED w ill blink. GA-7S748 Series Motherboard - 42 - English PnP/PCI Configurations CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are PnP/PCI Configurations PCI 4 IRQ Assignment PCI 1/5 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e F6:Fail-Safe Defaults ESC:Ex it F1:General Help F5:Prev ious Values F7:Optimized Defaults Figure 6: PnP/PCI Configurations PCI 4 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 4. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 4. PCI 1/5 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1/5. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 1/5. PCI 2 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 2. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 2. PCI 3 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 3. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 3. - 43 - BIOS Setup English PC Health Status CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are PC Health Status Vcore DDR25 +3. 3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed OK OK OK OK 45°C 5113 RPM 0 RPM Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 7: PC Health Status Current Voltage (V) Vcore / DDR25 / +3. 3 V / +12V Detec t sy stem' s v oltage status automatic ally . Current CPU Temperature Detec t CPU tem perature automatic ally . Current CPU/SYSTEM FAN Speed (RPM) Detec t CPU/Sy stem Fan speed status automatic ally . GA-7S748 Series Motherboard - 44 - English Frequency/Voltage Control CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Frequency /Voltage Control Linear Frequency Control x CPU Clock (MHz) x DRAM Clock (MHz) AGP Voltage Control DRAM Voltage Control CPU Voltage Control [Disabled] 100 AUTO [Normal] [Normal] [Normal] Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e F6:Fail-Safe Defaults ESC:Ex it F1:General Help F5:Prev ious Values F7:Optimized Defaults Figure 8: Frequency /Voltage Control Linear Frequency Control Disabled Enabled Disable this function. (Default v alue) Enable this function. CPU Clock (MHz) 100~355 Select CPU Clock to 100MHz~355MHz. For pow er End-User use only ! DRAM Clock (MHz) Please set DRAM Clock according to y our requirement. If y ou use DDR266 DRAM module, please set "DRAM Clock(MHz)" to Auto or 266. If y ou use DDR333 DRAM module, please set "DRAM Clock(MHz)" to Auto or 333. For pow er End-User use only ! - 45 - BIOS Setup English AGP Voltag e Control Normal +0. 1V +0. 2V Set AGP Voltage Control to Normal. (For AGP 4X only ) DRAM Voltage Control Normal +0. 1V Set DRAM Voltage Control to Normal. [. . . ] Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address (English): http://www. gigabyte. com. tw WEB address (Chinese): http://chinese. giga-byte. com -- U. S. A. Support : http://www. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. giga-byte. com -- Germany G. B. T. TECHNOLOGY TRADING GMBH Address: Friedrich-Ebert-Damm 112 22047 Hamburg TEL: +49-40-2533040 (Sales) +49-1803-428468 (Tech. ) FAX: +49-40-25492343 (Sales) +49-1803-428329 (Tech. ) Tech. [. . . ]