User manual GIGABYTE GA-7N400E-L

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X. AGP 4 X/8 X notc h Caution: AGP 2X card is not supported by nVIDIA® nForceTM 2 400. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] (Default Value) Use over colocked settings for higher performance but with higher risk of instability. Allows full customization of performance options. Incorrect using it m ay cause your system to fail. For power End-User use only! FSB Frequency 100 MHz 133 MHz 166 MHz 200 MHz Set FSB frequency at 100MHz. Set FSB frequency at 200MHz. - 39 - BIOS Setup 7n400e_1001_b. p65 39 2003/7/17, ¤U¤È 02:36 English MemoryFrequency By SPD 50%~200% Auto Set m emory frequency by SPD. Set the best m emory frequency for system. Incorrect using it m ay cause your system to fail. For power End-User use only! Resulting Frequency The value depends on FSB/M emory Frequency. AGP Frequency Normal Set the best AGP frequency for system. For power End-User use only! GA-7N400E(-L) Motherboard - 40 - 7n400e_1001_b. p65 40 2003/7/17, ¤U¤È 02:36 Integrated Peripherals CM OS Setup Utility-Copyright (C) 1984-2003 Award Software On-Chip Prim ary PCI IDE On-Chip Secondary PCI IDE USB Host Controller USB Keyboard Support USB M ouse Support AC97 Audio Onboard LAN Chip(* ) Onboard LAN Boot ROM (* ) Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port M ode ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ Integrated Peripherals [Enabled] [Enabled] [V1. 1+V2. 0] [Disabled] [Disabled] [Auto] [Enabled] [Disabled] [3F8/IRQ4] [2F8/IRQ3] [Normal] Half [378/IRQ7] [ECP] [3] [201] [330] [10] [Enabled] Enabled onboard IDE Port [Disabled] Disabled onboard IDE Port Item Help Menu Level u If a hard disk controller card is used, set at Disabled English higf: Move Enter:Select +/-/PU/PD: Value F10: Save ESC:Exit F5: Previous Values F6: Fail-Safe Defaults Figure 5: Integrated Peripherals F1: General Help F7: Optimized Defaults (*)For GA-7N400E-L only. - 41 - BIOS Setup 7n400e_1001_b. p65 41 2003/7/17, ¤U¤È 02:36 English On-Chip Primary PCI IDE Enabled Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE Enabled Disabled Enable onboard 2nd channel IDE port. (Default value) Disable onboard 2nd channel IDE port. USB Host Controller Disabled V1. 1+V2. 0 V1. 1 Disable USB controller. (Default Value) Set USB controller at USB1. 1. USB KeyboardSupport Enabled Disabled Enable USB Keyboard Support. (Default value) USB Mouse Support Enabled Disabled Enable USB Mouse Support. (Default value) AC97 Audio Auto Disabled Auto detect AC'97 audio function. (Default Value) Disable AC'97 audio function. Onboard LAN chip(*) Enabled Disabled Auto detect onborad LAN function. (Default Value) Disable this function. (*)For GA-7N400E-L only. GA-7N400E(-L) Motherboard - 42 - 7n400e_1001_b. p65 42 2003/7/17, ¤U¤È 02:36 Onboard LAN Boot ROM(*) This function decide whether to invoke the boot ROM of the onboard LAN chip. (Default value) English Onboard Serial Port 1 Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto Disable onboard Serial port 1. (Default value) Enable onboard Serial port 1 and address is 2F8, using IRQ3. BIOS will autom atically setup the port 1 address. Onboard Serial Port 2 Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto Disable onboard Serial port 2. (Default value) Enable onboard Serial port 2 and address is 3E8, using IRQ4. BIOS will autom atically setup the port 2 address. UARTMode Select This item allows you to determine which Infra Red(IR) function of Onboard I/O chip. Set onboard I/O chip UART to ASKIR Mode. (*)For GA-7N400E-L only. - 43 - BIOS Setup 7n400e_1001_b. p65 43 2003/7/17, ¤U¤È 02:36 English UR2Duplex Mode This feature allows you to seclect IR m ode. This function will available when "UART Mode Select" doesn't set at "Normal" nor "SCR". (Default Value) IR Function Duplex Full. Onboard Parallel port This feature allows you to select from a given set of parameters if the parallel port uses the onboard I/O controller. [. . . ] Integrated Peripherals--> Onboard H/W Serial ATA: "enable" Then it depends on the SATA mode that you need to set "RAID" to RAID mode or "BASE" to normal ATA mode in the item named Serial ATA function. Question 12:For the M/B which have RAID function, how to set in the BIOS in order to bootup from IDE3, 4 by either RAID or ATA mode? English Answer:Please set in the BIOS as follow: 1. Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. Question 13:How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ? [. . . ]