User manual GIGABYTE GA-6VXC7-4X

[. . . ] FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device , pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The system will halt and the following error message will appear in the mean time. Enabled Activate automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table No warning message to appear when anything attempts to access the boot sector or hard disk partition table. (Default Value) Disabled · Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512 K for systems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard. The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map. Other Memory This refers to the memory located in the 640 K to 1024 K address space. DOS uses this area to load device drivers to keep as much base memory free for application programs. Most use for this area is Shadow RAM Extended Memory 34 6VXC7-4X Motherboard BIOS Features Setup AMIBIOS SETUP ­ BIOS FEATURES CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved 1st Boot Device 2nd Boot Device 3rd Boot Device S. M. A. R. T for Hard Disks BootUp Num-Lock Floppy Drive Seek Password Check Processor Serial Number :Floppy :IDE-0 :CDROM :Disabled :On :Disabled :Setup :Disabled ESC : Quit : Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift)F2 :Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Figure 3: BIOS Features Setup · 1st / 2nd / 3rd Boot Device The default value is Floppy or LS-120 / ZIP A: or ATAPI ZIP C: or CDROM or SCSI or NET WORK / I20 or IDE-0~IDE-3 or Disabled. Floppy LS / ZIP A: CDROM SCSI NETWORK IDE-0~IDE-3 Disabled ATAPI ZIP C: Boot Device by Floppy. Boot Device by ATAPI ZIP C:. 35 BIOS Setup · S. M. A. R. T. (Default Value) · Boot Up Num-Lock On Off Keypad is number keys. (Default Value) Keypad is arrow keys. · Floppy Drive Seek During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks. Note that BIOS can not tell from 720, 1. 2 or 1. 44 drive type as they are all 80 tracks. BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360. (Default Value) Disabled · Password Check Setup Always Set Password Check to Setup. (Default Value) Set Password Check to Always. · Processor Serial Number Disabled Enabled Disabled CPU Serial Number. (Default Value) Enabled CPU Serial Number. 36 6VXC7-4X Motherboard Chipset Features Setup AMIBIOS SETUP ­CHIPSET FEATURE CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved *** DRAM Timing *** Top Performance SDRAM Timing by SPD SDRAM CAS# Latency DRAM Frequency C2P Concurrency & Master DRAM Integrity Mode AGP Mode AGP Comp. [. . . ] All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP INTEGRATED PERIPHERALS HARDWARE MONITOR SETUP SUPERVISOR PASSWORD USER PASSWORD PNP/PCI CONFIGURATION IDE HDD AUTO DETECTION Enter new supervisor password: LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS SAVE & EXIT SETUP EXIT WITHOUT SAVING ESC : Quit : Select Item (Shift) F2 : Change Color F5 : Old Values F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Chang /Set /Disabled Password Figure 11: Password Setting Type the password, up to eight characters, and press <Enter>. The password typed now will clear the previously entered password from CMOS memory. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. [. . . ]