User manual GIGABYTE GA-6VTXE-A

[. . . ] FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device , pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Floppy LS / ZIP A: CDROM SCSI NETWORK IDE-0~IDE-3 Disabled ATAPI ZIP C: Boot Device by Floppy. Boot Device by ATAPI ZIP C:. 34 6VTXE(-A) Motherboard · S. M. A. R. T. (Default Value) · Interrupt Mode APIC PIC Through IOAPIC generate more IRQ for system use. (Default value) Use AT standard IRQ controllers to generate IRQ. When you already have IOAPIC enable system and want to upgrade the system please note, since running an IOAPIC enabled OS (like Windows NT, Windows 2000, Windows XP. . . ) system with none IOAPIC HW support will cause the system to hang. Following are some situations users might run into: 1. An IOAPIC enabled OS and change the BIOS setting from IOAPIC to PIC, this will cause your system to hang. · Boot Up Num-Lock On Off Keypad is number keys. (Default Value) Keypad is arrow keys. · Floppy Drive Seek During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks. Note that BIOS can not tell from 720, 1. 2 or 1. 44 drive type as they are all 80 tracks. BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360. (Default Value) Disabled · Password Check Setup Always Set Password Check to Setup. (Default Value) Set Password Check to Always. · Processor Serial Number Disabled Enabled Disabled CPU Serial Number. (Default Value) Enabled CPU Serial Number. 35 BIOS Setup Chipset Features Setup AMIBIOS SETUP ­CHIPSET FEATURE CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved *** DRAM Timing *** Top Performance SDRAM Timing by SPD SDRAM CAS# Latency DRAM Frequency RAS# Drive :Disabled :Disabled :3 :Auto :24mA C2P Concurrency & Master DRAM Integrity Mode AGP Mode AGP Comp. Driving AGP Aperture Size USB Controller USB Legacy Support DRAM Drive Strength Delay DRAM Read Latch Memory Data Drive SDRAM Command Drive Memory Address Drive CAS# Drive :Enabled :Disabled :4X :Auto :64MB :Enabled :Disabled :Auto :1. 5ns :6Ma :24MA :24MA :12Ma ESC : Quit : Select Item F1: Help PU/PD/+/- : Modify F5: Old Values (Shift)F2 :Color F6: Load Fail-Safe Defaults F8:Flash Utility F7: Load Optimized Defaults Figure 4: Chipset Features Setup · Top Performance Disabled Enabled Set Top Performance is disabled. (Default Value) Set Top Performance is enabled. · SDRAM Timing by SPD Disabled Enabled SDRAM Timing by SPD Function Disabled. (Default Value) SDRAM Timing by SPD Function Enabled. · SDRAM CAS# Latency 3 2 For Slower SDRAM DIMM module. (Default Value) For Fastest SDRAM DIMM module. · DRAM Frequency Auto 100MHz 66MHz 133MHz Set DRAM Frequency automation. Set DRAM Frequency is 133MHz. 36 6VTXE(-A) Motherboard · C2P Concurrency & Master Enabled Disabled Enabled C2P Concurrency & Master. (Default Value) Disabled C2P Concurrency & Master. · DRAM Integrity Mode ECC Disabled For 72 bit ECC type DIMM Model. Driving is Manual. · AGP Aperture Size 4MB 8MB 16MB 32MB 64MB 128MB 256MB Set AGP Aperture Size to 4MB. Set AGP Aperture Size to 256 MB. · USB Controller Enabled Disabled USB Controller Function Enabled. (Default Value) USB Controller Function Disabled. · USB Legacy Support Keyboard Keyb+Mouse Disabled Set USB Legacy Support Keyboard. [. . . ] Current CPU Fan Speed :5487 RPM Current System Fan Speed :0 RPM Vcore :2. 075V +3. 300V :3. 590V +5. 000V :5. 119V +12. 000V :11. 926V ESC : Quit : Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift)F2 :Color F6 : Load Fail-Safe Defaults F8:Flash Utility F7 : Load Optimized Defaults Figure 10: Hardware Monitor · ACPI Shutdown Temp. (°C / °F) (This function will be effective only for the operating systems that support ACPI Function. ) Disabled 60°C / 140°F 65°C / 149°F 70°C / 158°F 75°C / 167°F Disable ACPI Shutdown function. > 75°C / 167°F system will automatically power off. · · Current CPU Temp. (°C / °F) Detect CPU Temperature automatically. Current System Temp. [. . . ]