User manual GIGABYTE GA-6OMM7E

[. . . ] FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] For EGA, VGA, SVGA, or PGA monitor adapters Color Graphics Adapter, power up in 40 column mode Color Graphics Adapter, power up in 80 column mode Monochrome adapter, includes high resolution monochrome adapters · Halt on The category determines whether the computer will stop if an error is detected during power up. NO Errors All Errors All, But Keyboard All, But Diskette All, But Disk/Key The system boot will not stop for any error that may be detected and you will be prompted. Whenever the BIOS detects a non-fatal error the system will be stopped. The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) The system boot will not stop for a disk error; it will stop for all other errors. The system boot will not stop for a keyboard or disk error; it will stop for all other errors. 47 BIOS Setup · Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512 K for systems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard. The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map. Extended Memory 48 6OMM7E Motherboard Advanced BIOS Features CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software Advanced BIOS Features Virus Warning Disabled Item Help BIOS Flash Protection Disabled First Boot Device Floppy Menu Level Allows you to Second Boot Device HDD-0 choose the VIRUS Third Boot Device LS120 Warning feature Boot Up Floppy Seek Enabled For IDE Hard disk Boot Up NumLock Status On Boot sector Security Option Setup Protection. Capability Disabled Function is enable Report No FDD For WIN 95 No And someone Attempt to write Data into this area , BIOS will show A warning Message on Screen and alarm beep :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4: Advanced BIOS Features · Virus Warning If it is set to enable, the category will flash on the screen when there is any attempt to write to the boot sector or partition table of the hard disk drive. The system will halt and the following error message will appear in the mean time. Enabled Activate automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table. No warning message to appear when anything attempts to access the boot sector or hard disk partition table. (Default value) Disabled 49 BIOS Setup · BIOS Flash Protection Enabled Disabled Enabled BIOS Flash Protection. (Default Value) · First / Second / Third Boot device Floppy LS120 ZIP100 HDD-0~3 SCSI CDROM Disable LAN Select your boot device priority by Floppy. Select your boot device priority by LAN. · Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1. 2 M or 1. 44 M drive type as they are all 80 tracks. (Default value) BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. Disabled · Boot Up NumLock Status On Off Keypad is number keys. (Default value) Keypad is arrow keys. · Security Option This category allows you to limit access to the system and Setup, or just to Setup. System Setup The system can not boot and can not access to Setup page will be denied if the correct password is not entered at the prompt. [. . . ] The password typed now will clear the previously entered password from CMOS memory. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. [. . . ]