User manual GIGABYTE GA-660

[. . . ] After installing the peripheral device, the user should check everything again, and prepare to power-on the system. 3. 13. KEYBOARD SETTING FUNCTION After booting the O. S. , there are some special functions used by keyboard as follows: "CTRL_ALT_DEL" - Pressing these keys simultaneously will cause system to Warm Start (Software Reset). 3-7 GA-660 4. BIOS CONFIGURATION Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS SRAM so that it retains the Setup information when the power is turned off. 4. 1. ENTERING SETUP Power ON the computer and press <Del> immediately will allow you to enter Setup. [. . . ] Stop CPU FAN when entering Suspend mode. · Resume by Ring The default value is Disable. Power ON system when Modem Ring On. · IRQ 8 Break Suspend The default value is Disable. Enable IRQ8(Timer) wake up system from Suspend. · Resume by Alarm The default value is Disabled. Enable alarm function to POWER ON system. · Date / Time Alarm The default value is Disabled. Set up the Time for ALRM function. · IRQ [3-7, 9-15] , NMI The default value is Enabled. Enable monitor IRQ [3-7, 9-15] for Green event. 4-19 BIOS Configuration · Primary IDE 0/1 The default value is Disabled. Enable monitor Primary IDE 0/1 for Green event. · Secondary IDE 0/1 The default value is Disabled. Enable monitor Secondary IDE 0/1 for Green event. · Floppy Disk The default value is Enabled. Enable monitor Floppy Disk for Green event. · Serial Port The default value is Enabled. Enable monitor Serial Port for Green event. · Parallel Port The default value is Disabled. Enable monitor Parallel Port for Green event. 4-20 GA-660 4. 9. Disable UDMA function. · On-Chip Primary IDE The default value is Enabled. Disable onboard 1st channel IDE port. · On-Chip Secondary IDE The default value is Enabled. Disable onboard 2nd channel IDE port. · USB Keyboard Support The default value is Disabled. Disable USB Keyboard Support. · Onboard FDD Controller The default value is Enabled. Disable onboard FDD port. · Onboard Serial Port 1 The default value is COM1/3F8. Onboard Serial Port 2 The default value is Auto. 4-25 · BIOS Configuration Auto COM1/3F8 COM2/2F8 COM3/3E8 COM4/2E8 Disabled BIOS will automatically setup the port B address. Disable onboard Serial port B. · Onboard Parallel port The default value is 378/IRQ7. Enable onboard LPT port and address is 3BC/IRQ7. · Onboard Parallel Mode The default value is SPP. LOAD SETUP DEFAULTS ROM PCI / ISA BIOS LOAD SETUP DEFAULTS AWARD SOFTWARE, INC. STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP EXIT WITHOUT SAVING PNP/PCI CONFIGURATION Load SETUP Defaults (Y/N)?N INTEGRATED PERIPHERALS LOAD SETUP DEFAULTS ESC F10 : Quit : Save & Exit Setup (Shift)F2 : Select Item : Change Color Load SETUP Defaults except Standard CMOS SETUP Figure 4. 7: Load Setup Defaults · Load SETUP Defaults To load SETUP defaults value to CMOS SRAM, enter "Y". [. . . ] Verify 8259 Channel 1 masked interrupts by alternately turning off and on the interrupt lines. Verify 8259 Channel 2 masked interrupts by alternately turning off and on the interrupt lines. Verify NMI can be cleared. B-2 GA-660 Check) 1A 1B-1E 1F Reserved Set EISA Mode If EISA non-volatile memory checksum is good, execute EISA initialization. Test EISA Configuration Memory Integrity (checksum & communication interface). [. . . ]