User manual GIGABYTE BLUE EYE

[. . . ] 6 Hold-Down Plates Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Water Block and VGA Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Water Tube Installation for Single VGA Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Any damage arising from the use of liquids other than Gigabyte Liquid Coolant is not covered by the warranty. 3 English Product Appearance Introduction Inlet Product Specifications Product Serial Number: Model: Dimensions: Materials: Flow Meter: ATi CrossFire Supported: nVidia SLi Supported: GPU Compatibility: Blue Eye VGA Water Block GH-WPBV1 113 x 61. 5 x 40. 5 mm Cooper, PC Cover Yes (UV Reaction) Yes Yes Please refer to Page 6; 1-2 Hold-Down Plates Introduction Outlet Base Feature Summary 1. Before the installation, please power down the computer and unplug the power cord. Blue LED with UV inductive current meter to display current status directly. Large water block with pure cooper base (specially water routing designed) All-purpose design, supporting most of water-cooling systems on the market. (1/4", 3/8", and 1/2" tubing) Skid-proof and easy-to-install tube clamps Hair-lined finished aluminum plate Please refer to the English version for all pictures. 4 Component List English (1) 1/4" tube x 1 (2) RAM heatsinks x 16 (3) 1/2" tube clamps x 4 (4) 3/8" tube clamps x 4 GH-WPBV1 VGA Water Block (5) 1/4" tube clamps x 10 (6) 1/2" tube splitters x 2 (7) 3/8" tube splitters x 2 (8) 1/4" tube splitters x 2 (9) Screws x 4 (10) Spring loaded screws x 4 (11) Hold-down plates (12) Base plate (13) Washers x 4 (14) Wrench (15) Grease (16) User manual 5 English I. Hardware Installation 1-1 VGA Fan Disassembly Please disassemble the fan on the VGA Card on your own. 1-2 Hold-Down Plates Introduction There are three combinations for the hold-down plate installations. Type A (Factory Default) Type B Type A supports the following VGA Cards. PCIE nVIDIA ATI 7900 X1900 7800 X1800 6800 AGP nVIDIA ATI 6800 Type B supports the following VGA Cards. PCIE nVIDIA ATI 7300 X850 6200 X700 5750 X600 AGP nVIDIA ATI 1600 X800 X700 9800 9600 6 Type C Take Type B for example. a, place the disc hold-down plate with the engraved Gigabyte logo facing up, so that the mounting holes on the disc hold-down plate match with the mounting holes on the base plate, and secure it with a fastener (as shown in Fig. a Mounting holes on the base plate 1-3 Hold-Down Plates Installation Please decide the type (Type A, Type B, or Type C) of hold-down plate for your VGA Card, depending on the position of the mounting holes. Secure the disc hold-down plate by tightening the screws (Component 9) with the wrench (Component 14) as shown in Fig. b 7 English 1-4 Water Block and VGA Card Installation Apply the grease on the VGA chipset as shown in Fig. c. Place the base plate (Component 12) in the desired position as shown in Fig. f. Insert the screws on the water block into the mounting holes as shown in Fig. f Bolt the base plate using the supplied spring loaded screws (Component 10) as shown in Fig. e, determine the position of the base plate (Component 12) so that its mounting holes line up with the mounting holes on the VGA radiator. Place the washers (Component 13) on the lined up mounting holes, as shown in Fig. [. . . ] Procedure 3: Connect one end of the supplied 1/4" water tube (Component 1) to the supplied 1/2" splitter (Component 8) and the other end to the VGA water block 1 inlet. Connect the VGA water block 1 outlet and the VGA water block 2 inlet with another supplied 1/4" water tube (Component 1). Finally connect one end of the other supplied 1/4" water tube (Component 1) to the VGA water block 2 outlet and the other end to the supplied 1/2" splitter (Component 8). [. . . ]