User manual GEMINI MPX-3

[. . . ] POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. LIGHTNING: For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. [. . . ] PITCH: The PITCH (25) button activates the PITCH CONTROL SLIDE (27) PITCH BEND: Buttons for PITCH BEND (26), lower or raise the pitch percentage (- or +) 4% when pressed. PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (27) up or down will lower or raise the pitch percentage (- or +) 4%, 8%, & 16%. VPS (VARIABLE PITCH SELECTOR) 4%, 8% & 16%: Use the VPS (28) buttons use to change the PITCH settings from 4%, 8%, & 16%. ROBO START: Using ROBO START (29) enables you to alternate play between two CDs using both sides. Your state-ofthe-art professional CD Player is backed by a three-year warranty that excludes lasers, which are covered by a separate one-year warranty. Prior to use of this unit, we suggest you carefully read the following instructions. Your Gemini MPX-3 CD Player comes equipped with ADCS (Automatic Disc Calibration System), a unique state-of-the-art feature. CDs are produced by a variety of manufacturers and recorded by many different professional companies as well as the do-ityourselfers at home. The ADCS automatically adjusts the laser in your MPX-3 CD Player for each individual CD you insert into the tray, to give you the best possible performance for every CD you play regardless of how it was manufactured or how it was recorded. With this exclusive system you always get consistent and reliable performance as well as exceptional sound quality every time you play a CD. PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR (10) displays the remaining play time and time elapsed for each track. The display flashes slowly when the track has 15 seconds remaining and pulses rapidly when play time is down to 5 seconds. pLAY/PAUSE : Each press of PLAY/PAUSE (11) causes the operation to change from PLAY to PAUSE or PAUSE to PLAY. CUE/PREVIEW: With the unit in the PLAY mode and after the CUE POINT has been programmed, pressing CUE/PREVIEW (12) will cause the CD player to enter the PAUSE mode at the programmed CUE POINT. Holding down the CUE/PREVIEW (12) button changes the function to PREVIEW and starts the CD from the programmed CUE POINT. releasing the CUE/PREVIEW (12) button will return the CD laser to the preset CUE POINT. SEARCH (FOLDER/FILE) : The SEARCH (13) buttons are used to move forward or reverse while in PLAY or PAUSE mode. In MP3 MODE use the SEARCH (13) buttons to view which FOLDER/FILE (13) is being read. Press FOLDER to view a FOLDER, then press FILE to view the FILE from the selected FOLDER. If the JOG WHEEL (22) is in TRACK MODE the FOLDER/FILE (13) buttons will correspond with which FOLDER or FILE is being viewed, the TRACK SEARCH (14) buttons also fuction like the JOG WHEEL (22). TRACK SEARCH : The TRACK SEARCH (14) buttons let you select a track to play. Do not use this CD player at temperatures below 41°F/5°C or higher than 95°F/35°C. [. . . ] Press PLAY/PAUSE (11) button on the playing side to start play from the cue point on the other CD deck. If a disk will not play, check to see that it was loaded correctly (label side up) and that the CD unit is on a flat, level, stable surface. Many CDs are recorded "out of spec" and skip on most or all CD players. Before sending the unit to an authorized Gemini service technician, insert a disc that plays properly in another unit. [. . . ]