User manual GATEWAY LN-520

[. . . ] LN-520 Digital A/V Receiver INTRODUCTION READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Center width control("C-WID", default value: 0) This adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees. Dimension control("DIMEN", default value: 0) This gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from -4 to +2. 2 While displaying the desired parameter, adjust it as desired. 3 Repeat the above steps 1 and 2 to adjust other parameters. ADJUST UP(>), DOWN(<) · If the parameter display disappears, start from the step 1 again. www. gateway. com 28 OPERATIONS Downmixing into 2 front channels · Allows the multi - channel DTS, Dolby Digital or MPEG signal to be reproduced through only two speakers or through headphones. · When the digital signals from the DTS, Dolby Digital or MPEG program sources are input in available surround mode, press the STEREO button. · To cancel the 2 - CH downmix mode, select the desired surround mode with the DSP MODE DOWN ( ) or UP( ) button. · When the playback of the source on the player is stopped, interrupted, etc. , the 2 - CH downmix mode is not canceled even though " ST" and the DTS or Dolby Digital indicators go off. · If the headphones are plugged while the digital signals from the DTS, Dolby Digital or MPEG program sources are being input, it will enter the 2CH downmix mode automatically and if the headphones are unplugged in the 2-CH downmix mode, it will return to the previous mode. STEREO · "ST" indicator lights up and "2 CH DOWNMIX" is scrolled, meaning it enters the 2-CH downmix mode, and then the discrete multi-channels(except LFE) are mixed down into 2 front channels. 29 www. gateway. com OPERATIONS LISTENING TO RADIO BROADCASTS To select the tuner, INPUT SELECTOR TUNER or To select the desired band DIGITAL INPUT · Each time this button is pressed, the band is changed as follows: FM STEREO FM MONO AM · When FM stereo broadcasts are poor because of weak broadcast signals, select the FM mono mode to reduce the noise, the FM broadcasts are reduced in monaural sound. AM/FM MODE BAND FREQUENCY Manual tuning Manual tuning is useful when you already know the frequency of the desired station. Auto tuning 1 Select the tuning mode. DECODING 1 Select the tuning mode. DECODING TUNE MODE TUNE MODE · Each time this button is pressed, the mode changes as follows; Tuning mode : "PRESET" goes off. Preset mode : "PRESET" lights up. 2 ADJUST Press the below button for more than 0. 5 second. TUNING/PRESET 2 ADJUST Press the below button repeatedly until the right frequency has been reached. or TUNE -, + TUNING/PRESET or TUNE -, + · The tuner will now search until a station of sufficient strength has been found. · If the station found is not the desired one, simply repeat this operation. · When pressing the TUNE +/- buttons on the remote control, you need not select the tuning mode on step 1. www. gateway. com 30 OPERATIONS Presetting radio stations · You can store up to 30 preferred stations in the memory. 2 Press the MEMORY button. SETUP MEMORY 1 3 ADJUST Tune in the desired station with auto or manual tuning. · "MEM" is flickering for 5 seconds. Select the desired preset number (1~30) and press the MEMORY button. SETUP TUNING/PRESET or PRESET -, + MEMORY · The station has now been stored in the memory. · A stored frequency is erased from the memory by storing another frequency in its place. · If "MEM" goes off, start again from the above step 2. 4 1 Repeat the above steps 1 to 3 to memorize other stations. Tuning to preset stations After selecting the tuner as an input source, select the preset mode. DECODING 2 Select the desired preset number. ADJUST TUNING/PRESET TUNE MODE or PRESET -, + · Then "PRESET" lights up. · When pressing the PRESET +/- buttons on the remote control, you need not select the preset mode on step 1. Scanning preset stations in sequence · The receiver will start scanning the stations in the preset sequence and each station is received for 5 seconds. · At the desired station, press this button again to stop scanning. · When pressing this button without selecting the tuner, the tuner will be selected automatically. P. SCAN 31 www. gateway. com OPERATIONS ANALOG AUDIO/VIDEO RECORDING · The analog signals (except front L/R channel) from the 7 CH DIRECT inputs as well as the digital signals from the coaxial or optical digital input cannot be recorded. · The volume and tone (bass, treble) settings have no effect on the recording signals. Recording with TAPE 1 Select the desired input as a recording source except for TAPE. 2 3 Start recording on the TAPE. Start play on the desired input. INPUT SELECTOR or TUNER AUX VIDEO1 VIDEO2 VIDEO3 Dubbing from video components onto VIDEO 1 2 3 Start recording on the VIDEO 1. 1 Select VIDEO 2 or VIDEO 3 as a recording source. Start play on the VIDEO 2 or the VIDEO 3. INPUT SELECTOR or VIDEO2 VIDEO3 · The audio and video signals from the VIDEO 2 or the VIDEO 3 will be dubbed onto the VIDEO 1 and you can enjoy them on the TV set and from the speakers. Dubbing the audio and video signals separately onto VIDEO 1 Example) When dubbing the VIDEO 2 video signal and the CD audio signal separately onto VIDEO 1. 2 Press the OSD button on the remote control unit and select FUNCTION SELECT VIDEO SELECT VIDEO 2. (Refer to page 36. ) 1 Select AUX as an audio recording source. CD player should be connected to AUX jacks. OSD INPUT SELECTOR AUX or www. gateway. com 32 OPERATIONS 3 Start recording on the VIDEO 1. 4 Start play on the AUX and the VIDEO 2 respectively. · The audio signal from the AUX and the video signal from the VIDEO 2 will be dubbed and you can enjoy them on the TV set and from the speakers. If you select AUX for hearing and VIDEO 1 for seeing, whenever you select AUX, the VIDEO 1 is selected automatically as video input source. So you are sure to be observe the order and doing of the above steps 1 and 2. DIGITAL AUDIO RECORDING WITH MD RECORDER · Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to "CONNECTING AUDIO COMPONENTS"/ " CONNECTING VEDIO COMPONENTS"/"CONNECTING DIGITAL INs and OUT" on page 5~6 and the operating instructions of the MD recorder or CD recorder. Notes: · Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc. · In most DVDs as well as some CDs, etc. , digital recording may not be available depending on the signal format. [. . . ] and its subsidiaries and affiliates are intended beneficiaries of this Agreement. If there is any inconsistency between this Agreement and any other agreement included with or relating to products or services purchased from Gateway, this Agreement shall govern. This Agreement may not be modified, altered or amended without the written agreement of Gateway. Any additional or altered terms attached to your order shall be null and void, unless expressly agreed to in writing by Gateway. [. . . ]