User manual GARMIN GPSMAP 700 INSTALLATIONS INSTRUCTIONS

[. . . ] For future reference, write the serial number assigned to your GPSMAP 700 series chartplotter in the space provided. The serial number is located on a sticker on the back of the device. Chartplotter serial number: to install the GPSMAP 700 series chartplotter, you must: 1. the following additional installation options are not necessary in order to use the GPSMAP 700 series chartplotter. they have been included for your convenience: · ConnectingthechartplottertoaNMEA2000network(page6) · ConnectingthechartplottertoaGA30remoteGPSantenna(page6). [. . . ] NotE: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainlessanti-seizelubricanttothescrewbeforeusing. to install the GPSMAP 700 series chartplotter on the bail-mount bracket: 1. Slidethechartplotterontothebailmount, andtightenthemountingknobs. Flush Mounting the Chartplotter Hardware (included): · Flush-mounttemplate · Four35mmM4. 2× 1. 4screws tools required (not included): · Jigsaw · Drillanddrillbits--3/8in. (9. 5mm)and1/8in. (3mm) · Number2Phillipsscrewdriver · Centerpunchandhammer · Fileandsandpaper To flush mount a GPSMAP 700 series chartplotter: 1. Trim the template and ensure it will fit in the location where you want to flush mount thechartplotter. NotES: · Make sure the surface on which you mount the chartplotter has adequate open space behind it to fit the chartplotter and the connected cables, andmakesuretoleaveapproximately1/2in. (13mm)ofspaceontherightsideofthechartplottertoaccesstheSDcarddoorand suncover. · Toavoidinterference, mountaGPSMAP700serieschartplotteratleast32in. (813mm)fromamagneticcompass. Remove the protective liner and apply the template to the location at which you want to mountthechartplotter. Usinga3/8in. (9. 5mm)drillbit, drillapilotholeinsidethecornerofthetemplatetobegincuttingthemountingsurface. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the flush-mount template. Ifthetopandbottommountingcoversareattachedtothefrontofthechartplotter, removethembyunsnappingthecoversfromthesides. Place the chartplotter in the hole, and make sure that the mounting holes on the chartplotter line up with the pilot holes on the flush-mount template after cutting, sanding, and filing the hole. If they do not line up, mark the locations where the pilot holes need to be. NotE: If you are mounting the chartplotter in fiberglass, it is recommended to use a countersink bit to drill a clearance-counter bore through onlythetopgel-coatlayer. Thiswillhelptoavoidanycrackinginthegel-coatlayerwhenthescrewsaretightened. ecurelytightenthefourincluded35mmM4. 2×1. 4mountingscrewsthroughthechartplotterintothepilotholes. S NotE: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainlessanti-seizelubricanttothescrewbeforeusing. 11. Installthetopandbottommountingcoversbysnappingthemintoplace. GPSMAP 700 Series Installation Instructions Installing the Power/Data Cable The chartplotter comes with a power/data cable that connects the chartplotter to power and to optional NMEA 0183 devices. If applicable, the power/data cable also connects the chartplotter to a sonar transducer. The power/data cable does not connect the chartplotter to a NMEA 2000 network. For instructions on connecting the chartplotter to a NMEA 2000 network, see page 6. To help make the cable-routing process easier, the locking ring is packaged separately from the cable. [. . . ] Carefully press the cable into the correct port on the back of the chartplotter until it is firmly seated. Afterthecableisseated, turnthelockingringclockwiseuntilitistight. Becarefulnottoovertightenthelockingring. GPSMAP 700 Series Connectors NMEA 2000 connector Radar port Power/data connector External GPS antenna connector updating the Chartplotter Software The GPSMAP 700 series chartplotter may contain a software update SD card. If a software update SD card is not included, visit www. garmin. com to make sure your chartplotter software is up-to-date. To identify the version of software on your chartplotter, select or touch Configure > System > System Information. GPSMAP 700 Series Installation Instructions 7 Appendix Specifications Physical Specifications Specification Size Weight Display Case Temp. Range CompassSafe Distance Measurement W × H × D: 8 29/32×519/32×31/8in. (226×142×80mm) 2. 48lb. (1. 125kg) W × H: 6 × 3 19/32in. (152×91mm) FullyGasketed, high-impactplasticandaluminumalloy, waterprooftoIEC60529IPX-7 From5°Fto131°F(from-15°Cto55°C) 32in. (813mm) GPS Performance Specification Parameter Receiver Warm Acquisition Time Cold Reacquisition UpdateRate Accuracy GPS DGPS Velocity Measurement High-sensitivity12parallelchannel, WAAS-capablereceiver Approximately1sec. (Thedeviceisatornearthelastlocationatwhichyourecentlyacquiredsatellites. ) Approximately38sec. (Thedevicehasmovedmorethanabout500mi. [800km]sinceitwasturnedoff. ) <1sec. [. . . ]