User manual GARMIN GPS 17HVS 2006 2010 GPS 17 INSTALLATION

[. . . ] Within this period, Garmin will at its sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to installation errors, abuse, misuse, accident, or unauthorized alteration or repairs. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. [. . . ] Mount the GPSMAP 2006C/2010C in a location that provides a clear, glare-free view of the display and easy operation of the controls. If you experience difficulty installing the unit, contact Garmin Product Support or seek the assistance of a professional installer. Mounting Knob Bail Mount Mounting Holes GPSMAP 2010C Shown GPSMAP 2006C/2010C & GPS 17 3 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Surface Mount Tools · · · · Drill and Drill Bit Screwdriver Pencil Mounting Hardware (not included) NOTE: Mounting hardware (fasteners) not included. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least two inches of clearance behind the unit for the wiring. Using an appropriate size drill bit, drill pilot holes for the fasteners. Slide the unit into the bail mount and tighten the mounting knobs. To install the Bail Mount and unit: Bail Mount Mounting knobs Bail mount 4 GPSMAP 2006C/2010C & GPS 17 INSTALLATION INSTRUCTIONS Flush Mount Tools · · · · · · · · · · Flush Mount Template Jig saw Masking tape Scissors Drill Drill bits--1/8" (3 mm) and 3/8" (6 mm) 1/16" (2 mm) Allen (Hex) wrench Sockets or wrenches Hammer Center punch Trim the Flush Mount Template and tape it in the location you want. Using the center punch, indent the center of each mounting hole location. Using a 3/8" (6 mm) drill bit, drill a hole for a location to begin cutting the mounting surface. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. There is only a small amount of clearance between the case molding and the mounting holes. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16" (2 mm) Allen wrench to tighten the mounting studs until the stop contacts the case. The studs have a reusable thread-locking patch pre-applied from the factory. Place washers over the mounting studs, then thread on one hex nut per mounting stud. Install and tighten the second hex nut set on all four mounting studs to lock the first set in place. To flush mount the GPSMAP 2006C/2010C: 1. 5. Flush Mount TRIM TEMPLATE ALONG THIS LINE TO AID FITTING 230mm GPSMAP 2010/2010C/3010C CUT MOUNTING SURFACE ALONG INSIDE OF THIS LINE Be very careful when cutting this hole, there is only a small amount of clearance between the unit and the Mounting Hole. UNIT OUTLINE Flush Mounting the GPS 1. Using the Center Punch, indent the center of each Mounting Hole location. (Drilling the mounting holes before cutting the hole for the unit will allow for an easier installation. ) 4. Using a 3/8" (6mm) drill bit, drill a hole for a location to begin cutting the mounting surface. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. Be very careful when cutting this hole, there is only a small amount of clearance between the case molding and the Mounting Holes. Install the four Mounting Studs into unit by screwing the shorter, threaded section into the back of the unit. [. . . ] If the coax is run through the panel, seal the outside exit area with marine sealant. Mounting holes 6 GPSMAP 2006C/2010C & GPS 17 INSTALLATION INSTRUCTIONS To attach the enclosed pole mount to the GPS 17: 1. A SWITCH OR RELAY CAN BE USED TO SELECT BETWEEN VISUAL AND AUDIBLE ALERTS, IF REQUIRED Diagram 1 - Basic Hook-up 8 GPSMAP 2006C/2010C & GPS 17 INSTALLATION INSTRUCTIONS + SHIP'S BATTERY 10-32 VOLTS - GARMIN GSD 20 SOUNDER MODULE (SEE GSD 20 INSTALL INSTRUCTIONS) (-) (-) (-) 4. A GARMIN SOUNDER UNIT (OTHER THAN GSD 20) CAN PROVIDE WATER DEPTH, WATER TEMPATURE, AND SPEED VIA NMEA DATA FOR DISPLAY ON THE GPSMAP 2006/2010. Diagram 2 - Complete Interface GPSMAP 2006C/2010C & GPS 17 9 INSTALLATION INSTRUCTIONS Final Wiring Connection Once all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2006/2010. [. . . ]