User manual GARMIN GPS 400

[. . . ] 400/500 Series Display Interfaces Pilot's Guide Addendum · Goodrich STORMSCOPE® WX-500 Series II Weather Mapping Sensor · Goodrich SKYWATCH® Traffic Advisory System (Model SKY497) · Goodrich SKYWATCH® HP Traffic Advisory System (Model SKY899) · Bendix/King® KTA870 TAS/KMH880 Multi-Hazard Awareness System · Ryan TCAD 9900B and 9900BX Foreword This Pilot's Guide Addendum is written for Garmin 400/500 Main System Software Version 4. 00 (400 Series) and 4. 00 (500 Series) or above, and is not applicable for earlier software versions. Garmin International, Inc. , 1200 East 151st Street, Olathe, KS 66062, U. S. A. 44/1794. 519944 nd Fax 913/397. 8282 Fax 44/1794. 519222 Fax 886/2. 2642. 9099 Garmin®is a registered trademark of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin Ltd. [. . . ] Please note, however, that strike data is not typically updated on the Map Page while the panning cursor is on. Therefore, when the panned map is first displayed, the data is only a "snapshot" of conditions (as mentioned above, the strike rate will reflect viewable data only). Changing the Storm Data Display Range Storm data can be displayed on the 2000 nm zoom scale, but the data only goes out as far as the STORMSCOPE can report (200 nm). Scales greater than 500 nm do not display any further STORMSCOPE data. To select a storm data display range: 1. From the default Nav Page, turn the small right knob to select the Map Page. Turn the large right knob to select the desired lightning symbol option. Turn the small right knob to select the desired range and press ENT. 7 Getting Started Section 2 Goodrich STORMSCOPE Interface Main Page Sequence Weather Page--400 Series In addition to the Map Page, storm data can also be viewed on the Weather Page. In the 400 Series, When the STORMSCOPE is connected to the unit, the Weather Page appears after the Traffic Page in the sequence of Nav Pages (resulting in a total of eight pages). Default NAV Map Traffic NAVCOM Position Satellite Status VNAV Clearing discharge points from the Map Page. Weather Weather Page--500 Series In addition to the Map Page, storm data can also be viewed on the Weather Page. In the 500 Series, when the STORMSCOPE is connected to the unit, the Weather Page appears after the Traffic Page in the sequence of Nav Pages (resulting in a total of six pages). Changing the storm data display range on the Map Page. Default NAV Map Traffic NAVCOM Satellite Status 8 Weather Weather Display Getting Started Section 2 Goodrich STORMSCOPE Interface Main Page Sequence The Weather Page displays either a 360° or a 120° viewing angle. In normal operation, the current strike rate is displayed in the top right corner, accompanied in the top left corner by the word `LTNG'. When in strike mode, `Strike' is displayed in the lower right hand corner of the Weather Page and when the unit is in cell mode, `Cell' is displayed in the lower right hand corner of the Weather Page. To select the desired Weather Display Mode: 1. From the default NAV Page, rotate the small right knob to select the Weather Page. Select the desired display angle from the options menu and press ENT. Weather Display Interpretation For weather display interpretation, study the examples in the WX-500 Pilot's Guide which are designed to help you relate the cell or strike patterns shown on the display to the size and location of thunderstorms that may be near your aircraft. Stormscope Operation Strike Rate Storm Activity For weather display interpretation, study the examples in the WX-500 Pilot's Guide which are designed to help you relate the cell or strike patterns shown on the display to the size and location of thunderstorms that may be near your aircraft. Orientation Method Weather Mode Weather Display 9 Getting Started Section 3 SKYWATCHSequence Main Page Interface Introduction SECTION 3 SKYWATCH INTERFACE With the exception of traffic display range selections, all information in this section pertaining to the display and control of the Goodrich SKYWATCH (SKY 497) also applies to the Goodrich SKYWATCH HP (SKY 899) and the Bendix/King KTA 870/KMH 880--this includes TCAS-like symbology. Traffic display range selections are as follows: · SKYWATCH (SKY 497)--2 nm, 2 and 6 nm, 6 and 12 nm. · SKYWATCH HP (SKY 899)--2 nm, 2 and 6 nm, 6 and 12 nm, 12 and 24 nm. The Standby Screen appears when the SKYWATCH passes the power-up test. NOTE: when the system is in standby, the SKYWATCH does not transmit, interrogate, or track intruders. · Bendix/King KTA 870/KMH 880--2 nm, 2 and 6 nm, 6 and 12 nm, 12 and 24 nm, 20 and 40 nm. SKYWATCH Description Please, refer to the SKYWATCH Pilot's Guide for a complete description of the SKYWATCH system. Power-up Self-Test Check for the following test criteria on the Traffic Page during power-up: 1. If the SKYWATCH passes the power-up test and your aircraft both has a squat switch and is on the ground, the Standby Screen is displayed (see sidebar). If the SKYWATCH passes the power-up test and your aircraft both has a squat switch and is airborne, the Traffic Page is displayed on the 6-nm display range and in the normal altitude display mode. If the SKYWATCH passes the power-up test and your aircraft does not have a squat switch, the Standby Screen is displayed. If the SKYWATCH continues to fail, please refer to the failure response section in the SKYWATCH Pilot's Guide on actions to take. Traffic Page showing Bendix/King KTA 870/KMH traffic near the 40 nautical mile range. Press ENT to confirm operating mode and begin tracking intruder aircraft. Getting Started Section 3 SKYWATCHSequence Main Page Interface The FAILED message occurs when the system detects an error that prohibits further traffic display operation as long as this message stays on the screen. User-initiated Test A user-initiated test can only be performed when in standby or failed mode. In addition to the power-up test, the SKYWATCH performs a continuous self-test. A user-initiated test of the SKYWATCH Interface can also be performed. To perform a user-initiated test: 1. Turn the small right knob to select `Self Test?' and press ENT. Operating Mode is confirmed by the display of `OPER' in the upper right-hand corner of the Traffic Page. Voice Announcements See the SKYWATCH Pilot's Guide for information on voice announcements. Switching Between Standby and Operating Modes The unit must be in operating mode for traffic to be displayed. [. . . ] of altitude separation that is converging or maintaining altitude separation. TRFC: other traffic. 20 TCAD Setup Page Section 4 Ryan TCAD Interface The Ryan TCAD Setup Page is accessed from the Traffic Page. The definitions of the available options are listed in the TCAD Pilot's Handbook. To change a TCAD setup option: 1. The mode selection determines which shield definition to display and change. [. . . ]