User manual FBII OMNI-848EU

[. . . ] +DUGZLUHG:LUHOHVV6\VWHP 201, 201, (8 201, 201, (8 8VHU*XLGH ARMED READY STAY 1 4 7 2 5 8 0 3 6 9 # BYPASS INSTANT ARMED READY STAY 1 4 7 2 5 8 0 3 6 9 # ARM AC / LB 1 4 7 2 5 8 0 3 6 9 # INSTANT CODE BYPASS INSTANT READY CODE STAY BYPASS STAY INST LO BATT SPRV. CODE FIRE BURGLARY INSTRUMENTS, INC. N9939V2 4/01 Table Of Contents QUICK REFERENCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SYSTEM REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ARMING THE SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Events ranked from highest to lowest priority are alarm, trouble, open, and close. CHANGING THE PAGER PHONE NUMBER (FOLLOW-ME) You can change your pager follow-me phone number as follows if your installer enabled this feature: 1. Access pager number programming by pressing the following keys in sequence: [#], [5], and [8]. An acknowledgement tone sounds to indicate pager number programming has been accessed. The # , 5 , 8 command is accessible only while the system is disarmed and the dialer, dialer delay, and bell are not active. In pager phone number programming mode, only the LCD keypad provides visual display of the numbers already programmed or numbers that are being changed. The LED and fixed-word style keypads provide no visual keypad display of these numbers. - 21 - Using a Pager (cont) 2. Your new pager phone number may consist of up to 16 characters (1-9, 0). It may be necessary to add time to allow the pager to answer before dialing your pager number. (Entering a 2-second pause is optional and is not required to enter your pager phone number. ) If the [Code] key was pressed, it counts as one character. The keypad will emit a single acknowledgement chirp as each number is pressed. Press the [#] key after you have made your pager phone number changes. Pressing the [#] key saves your new pager number and nulls out the remaining locations. To exit without saving changes, press the [G] key to exit pager phone number programming. An acknowledgement tone sounds to indicate pager number programming has been exited. If you press the [G] key without first pressing the [#] key to save your new pager phone number, the system exits the pager phone number programming mode without saving the changes. If no key is pressed within 10 seconds, the pager phone number programming mode times out and exits automatically without saving any information entered. TURN PAGER REPORTING ON/OFF FOR THE PARTITION You can turn on/off the open-close reporting feature for a partition by pressing # , 8 . The display prompts you to toggle the feature on/off with the [#] key. TURN PAGER REPORTING ON/OFF FOR A USER You can turn on/off the open-close reporting feature for a user by entering the following : # , 7 , [master code] [user number] [4] NOTE: The # , 7 command is also used to assign a user to a different partition (see ASSIGNING PARTITIONS TO USERS on page 14). - 22 - Testing the System SYSTEM TEST It is recommended that you test your system once a week using the following procedure: NOTE: If your system is monitored, contact your central station before you perform this test. Then activate the system by opening a protected zone (for example: a window or door). If your system is connected to a central station, the keypad will sound the ringback tone to confirm that the signal was received. [. . . ] Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. However, even if the system responds to the emergency as intended, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. [. . . ]