User manual FARSTONE DRIVECLONE 2

[. . . ] DriveClone TM Version 2. 0 User's Guide Copyright Notice No part of this publication may be copied, transmitted, stored in a retrieval system, or translated into any language in any form or by any means without the expressed written permission of FarStone Technology, Inc. FarStone grants you the right to use one copy of the enclosed software program ("SOFTWARE") on a single computer. If the SOFTWARE is installed on a network, or more than one user can run the SOFTWARE at the same time, you must purchase an additional license for each additional user or computer. Trademarks FarStoneTM and DriveCloneTM are trademarks of FarStone Technology, Inc. Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft Corporation. [. . . ] To create a Bootable Disc, insert a blank CD/DVD disc into the recorder and click Utilities Bootable Disc. When the bootable disc has been created, click Finish to eject the disc. 4. 4. 2 Image Integrity Check Use this function to check if an image file created by DriveClone is restorable. Click Browse to select an image from either the hard drive, CD/DVD disc, network location or other movable storage medium, and then click Next to check the image. After the Image Integrity Check has completed, it will report the results in a dialog box. 4. 4. 3 Erase Disc You can use DriveClone Utilities to erase data from a re-writable disc, providing your drive supports the use of re-writable media (i. e. To erase a disc, insert the disc to be erased into the CD/DVD drive and select Utilities mode and click Next to begin theprocess. Select an erase Two Erase Modes: Quick Erase: Using this method, discs that are erased appear to be empty but the data is not physically removed. Quick Erase will take a short time to complete and will only erase the Table of Contents (TOC) of the disc. Compared to Quick Erase, Full Erase will take a longer time to complete, but it is less likely to run into a disc error when using a full erased disc to burn again. 4. 5 Settings You can set a standard for using the USB devices, and your local network configurations. 4. 5. 1 Set USB Standard DriveClone can back up to or restore from an image file that is on a USB device. To set a defaultUSB standard for your device, click Settings (shown below), choose a USB standard and click Apply. 18 Note If you select USB 2. 0, please make sure all your USB devices, eg. the USB storage medium, the port and the host adapter card, can support USB 2. 0. Otherwise, it will automatically revert to USB 1. 1 speed. 4. 5. 2 Network Settings DriveClone can back up to, or restore from a network location. To use this feature, you should first configure your network settings. To configure your network settings, click Settings from the main DriveClone interface and then click the Settings button in under Network. There are two tabs in the Network Settings window: General: The General tab is shown below. You can setup your network adaptor, IP address, Subnet mask and Default gateway from here. If you have more than one network adaptor on your system, select the adaptor to be used from the dropdown menu. IP Settings: Obtain an IP address automatically: If your network supports DHCP (Dynamic Host Configuration Protocol), choose this option to obtain an IP address automatically from a DHCP server or a Point-to-Point Protocol (PPP) dial-up network access server. DriveClone uses DHCP as the default option and will obtain the IP address of your computer automatically. IP address: Choose this option to manually specify IP address for your network. This option can be used when automatically obtaining IP address fails or the there is an IP address conflict. Advanced The Advanced tab is shown as below. 19 If your computer is on a Local Area Network (LAN), you can set the LAN settings so that you can back up images to or restore from a network location. DNS settings: Obtaining DNS server address automatically: DNS (Domain Name System) is an internet service that translates domain names into IP addresses. It is a system for name resolution suitable for network computers with fixed IP addresses. By default, DriveClone uses this option to obtain the DNS sever address automatically from the network. [. . . ] While FARSTONE continues to own the Software, you will have certain rights to use the Software after your acceptance of this license. Except as may be modified by a license addendum which accompanies this license, your rights and obligations with respect to the use of this Software are as follows: A. User License: (a) The "Software" can be used on a single computer and only by a single user at a time. (b) You can make one copy of the "Software" in machine-readable form, solely for back-up purposes, provided you reproduce FarStone's copyright proprietary legends. [. . . ]