User manual EARLEX LCS270

[. . . ] It has many added features; G Each tank is individually pressure tested. G G G sound indicates that you should proceed only with extreme care - stopping immediately if you hear a cracking sound or plaster starts to break loose. The steam stripper is safe for drywall/plaster board surfaces but whatever the material, it is always wise to check a small area before starting work properly. The heat generated by the boiler unit can mark carpets, soft furnishings, table tops, cabinets etc. [. . . ] Prior to the steam being produced a small amount of bubbling will occur at the steam plate. When the steam has been produced, lift the steam plate above the level of the tank outlet to allow condensed steam to run back down the hose and into the tank. If you are right handed hold the steam plate in your left hand and place flat against the wall where you wish to commence removing. If you are left handed you may find it easier to operate with the other hand. If the steam plate is fitted with a metal swivel joint, tighten hose nut to thread using two spanners. To fill the unit, remove the filler cap and fill to the maximum water level as shown on the glass panel at the end of the tank. DO NOT USE ADDITIVES - DO NOT OVERFILL. 3 Move the steam plate to the section immediately next to where you have just been working and use a wallpaper scraper to remove the section that has just been steamed. By working in this way you should be able to remove paper continually. You may have to leave the plate against the wall for longer periods with some papers or re-steam if not completely removed. The 230V unit will operate for approximately 1 1/2 hrs and the 110V unit will operate for approximately 3 1/4 hrs before requiring refilling. The water level is shown through the glass level indicator and should not be allowed to fall below minimum. If you require further use of the steamer, ensure unit is switched off and has stopped boiling. Slowly turn cap anti-clockwise, any remaining trapped steam will be released from beneath cap. Refill to the level indicator as before and follow above instructions. If the unit is allowed to boil dry this will operate and prevent further use. Switch the unit off and allow it to cool for at least 5 minutes, refill with water and then switch on again - the thermal cut-out should automatically re-set. When you have finished using the unit allow any remaining water to cool and then empty the unit. NEVER LEAVE WATER IN THE UNIT WHILST BEING STORED. Storage Brackets are fitted to the frame for the storage of the mains lead and hose. To recoil - wind the mains lead onto the brackets - then wind on the steam hose ensuring adequate length of hose is left to secure the steamplate into the clips on the opposite side. Slowly unscrew the cap, any remaining trapped steam will be released from the anti-discharge valve. [. . . ] ONLY QUALIFIED ELECTRICIANS SHOULD UNDERTAKE THIS WORK. IF YOU REQUIRE ANY FURTHER ASSISTANCE PLEASE CALL OUR HELPLINE ON 01483 454666 Monday - Friday 08:30 - 18:00 (excluding Bank Holidays) 5 Spare Parts List and Diagram PART NO. DESCRIPTION PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS 0004 0005 0006 0007 0008/A 0019 0020 0021 0022 0023 0027 0028 0029 0032 0038 0042 0047 0048 0049 0053 0055 0071 0117 0118 0123 0124 0127 0128 0134 QTY PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS 0136 0137 0138 0139 0140 0155 0200 0202 0302 0296 0301 0303 0316 0317 0321 3000 3001 3003 3004 3005 3006 3014 3037 Glass Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Heat Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Heating Element 2750W. . . . . . . . . . . . . . . . . . . . . . . [. . . ]