User manual DOMETIC NDR1292-S INSTALLATION
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DOMETIC NDR1292-S. We hope that this DOMETIC NDR1292-S user guide will be useful to you.
Manual abstract: user guide DOMETIC NDR1292-SINSTALLATION
Detailed instructions for use are in the User's Guide.
[. . . ] Ill Dometic
NDR 1292-S
INSTALLATION AND OPERATING INSTRUCTIONS
REFRIGERATOR FOR LP-GAS AND ELECTRIC OPERATION
NDR1292-S
FOR YOUR SAFETY If you smell gas: 1. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information consult a qualified installer, service agency or the gas supplier.
NEWDIMENSIONS
Contents:
Installation Operating Instructions Maintenance & Sewice Page 4 0 12
AVIS Cet appareil doit 6tre repark seulement par un reparateur autorise. [. . . ] If the CHECK indicator lamp(D) illuminates and the GAS mode indicator lamp (C) is off, the controls have failed to ignite the burner in the GAS mode. GAS operation may be reset by pressing the main power ON/OFF button (1) to the OFF then ON position. Press the TEMPERATURE SELECTOR button (3) until the lamp at the desired position is illuminated.
TO SHUT OFF THE REFRIGERATOR
The refrigerator may be shut off while in any mode of operation by pressing the main power ON/OFF button to the UP (OFF) position. This shuts off all DC power to the refrigerator, including the interior light.
GAS MODE
1. Press the AESlAUTOlGAS mode selector button (2) to turn OFF theAES/AUTO lamp (B). Within 45 seconds the burner should be ignited and operating normally. On the initial refrigerator start-up, it may take longer than 45 seconds to allow air to be purged from the gas line. If the gas does not ignite within 45 seconds the CHECK indicator lamp (D) will illuminate and the GAS mode indicator lamp (C)will go off To reset when the CHECK indicator lamp (D) is illuminated, press the main power ON/OFF button (1) to the OFF and then ON position. NOTE: Do not continue to reset GAS operation if the CHECK indicator lamp continues to be illuminated after several tries. Press the TEMPERATURE SELECTOR button (3) until the lamp at the desired position is illuminated.
9
E
F
G
DESCRIPTION OF OPERATING MODES
AESlAUTO MODE
When operating in the AES/AUTO mode, the AES/AUTO mode indicator lamp (6) will illuminate. The control system will automatically select between AC and GAS operation with AC having priority over GAS. Either the AC indicator lamp (A) or the GAS indicator lamp (C) will illuminate depending on the energy source selected by the control system. If the control system is operating with AC energy and it then becomes unavailable, the system will automatically switch to GAS. As soon as AC becomes available again the control will switch back to AC regardless of the status of GAS operation.
LIMP MODE OF OPERATION
This control system contains a feature where it will continue to operate the cooling system in the event of a failure of a major operating component. Two different modes of operation can occur in this category If for some reason the display module becomes non functional, the control system will revert to full automatic operation selecting the best energy source available with AC, GAS priority The temperature of the refrigerator will be maintained at the MID position within normal temperature tolerances. The power module will continually attempt to reestablish operation of the display module. The second limp mode of operation will execute when a failure of the temperature sensing device or associated electronic circuitry occurs. If this should occur, the control system will operate on the energy source selected via the control panel. The refrigerator will continue to operate in this mode indefinitely or until a new sensor is installed and the system is reset.
GAS MODE
When operating in the GAS mode theAES/AUTO mode indicator lamp (6) will be off and the GAS mode indicator lamp (C)will be illuminated. The control system will activate the ignition system and will attempt to light the burner for a period of approximately45 seconds. If unsuccessful, the CHECK indicator lamp (D) will illuminate and the GAS mode indicator lamp(C) will turn off. To restart GAS operation, press the main power ONI OFF button (1) to the OFF and then ON position. [. . . ] Check the AES control system by connecting/disconnetting 120 volt AC power. Compare the operation with the operation described in description of operating modes. The LP gas pressure should be checked and the main regulator re-adjusted if pressure is incorrect. 12 Shown in open position
BVRNER
/SPARK ELECTRODE
PRESSURE TEST PORT
The correct operating pressure is 11 inches of water column. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DOMETIC NDR1292-S
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DOMETIC NDR1292-S will begin.