User manual DIRT DEVIL DDC1800P

[. . . ] To ensure maximum efficiency of the Turbine Powerhead, make sure that any filters, bags and cleaning hoses in your vacuum system are clean and free of blockage. (C) CLEARING INTAKE NOZZLE If the Turbine or Intake nozzle become obstructed. Turn off Vacuum System and disconnect the Powerhead from wand and hose. Turn Powerhead over, and remove the clear belt cover, by first rotating the two latches counter clockwise until they align with the openings in the belt cover. Pull the belt cover away from the housing using the tab provided, then pull the belt cover out from under the baseplate. [. . . ] Check that a proper seal is made: UNIT PERFORMANCE IS DEPENDENT ON A PROPER SEAL!Secure the belt cover in place by rotating the two latches clockwise to the locked position. (D) CLEANING BRUSH Turn off vacuum system and disconnect Powerhead. These should be removed by unwinding them by hand or carefully cutting with scissors or other cutting tool. Keeping the beater brush clean will maintain efficiency. Page 2 (E) REMOVING THE DRIVE BELT AND BRUSH “It is recommended this procedure be performed by a Qualified Service Technician. ” Should the drive belt or brush become clogged with debris or need replacing: 1. Lift front of baseplate up from bumper, then pull baseplate free of unit. PLEASE NOTE: Correct brush and belt orientation; they must be re-installed correctly for proper function. Partially remove the bumper by lifting it free from the front and sides of the housing. Lift the lower belt shroud, brush, belt and support assembly out of the housing, and remove the belt from the brush. Leave upper belt shroud installed in the housing, unless stubborn debris remains lodged below it. Pull the right brush support (marked ‘R’) off the assembly and remove the brush from the shaft. Slide replacement brush onto the shaft so the large recess at one end of the brush goes on first and fits over the 4 ribs on the shaft support. Reassemble by inserting the tabs on the front of the base plate into the slots in the base housing, then secure the back of the brown base plate with the latch. Page 5 (E) BELT REPLACEMENT Remove brown base plate and belt cover (right side of Powerhead) by removing screw. Next, remove belt from pulley (may help to turn cleaning brush backwards slightly. ) (See Fig. Before replacing base plate and belt cover, make sure a “2” is showing at both ends of brush assembly (this number is stamped right on the bearing housing. ) (See Fig. Make sure also that no brush bristles are caught between the belt and brush roll gear. If brush bristles are worn, see BRUSH ROLLER ADJUSTMENT. (F) BRUSH ROLLER ADJUSTMENT To adjust brush to compensate for bristle wear, remove brown base plate. Finally, remove the belt from the pulley (it may help to turn cleaning brush backwards slightly). Turn brush assembly over and reinsert so that number “1” is showing at both ends. Note: The brush roll comes from the factory with a “2” showing at both ends of the brush roll assembly. Before replacing base plate and belt cover, make sure no brush bristles are caught between the belt and the brush roller gear. Page 6 OTHER REPAIRS For repairs or service beyond those described above, please contact your servicing distributor or dealer. LIMITED WARRANTY H-P PRODUCTS, INC. warrants that the turbine powerhead and the hand held turbine powerhead, when used for household purposes, pursuant to Seller’s instructions, will be free from defects in materials and workmanship for a period of one year from the date of the initial consumer purchase. warrants that the turbine powerhead or the hand held turbine powerhead, when used in a commercial application pursuant to Seller’s instructions, will be free from defects in materials and workmanship for a period of ninety (90) days from the date of the initial consumer purchase. [. . . ] This warranty is limited to the replacement of defective parts and any costs of shipping shall be incurred by the purchaser. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, AND H-P PRODUCTS, INC. SPECIFICALLY DISCLAIMS RESPONSIBILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES, AND LIMITS THE IMPLIED WARRANTY OF MERCHANTABILITY TO THE PERIOD OF EFFECTIVENESS OF THIS EXPRESS WARRANTY. (216) 875-5556 TROUBLE SHOOTING TURBINE POWERHEADS CAUTION Moving parts – disconnect from vacuum system before servicing unit PROBLEMS 1. [. . . ]