User manual DE DIETRICH DVY1010J

[. . . ] Section Before first use Connections Electricity connection Water connection Usage Information Water Softener Detergent Rinse - Aid Loading the Dishwasher Unloading the dishwasher 6 6 6 7 8 8 10 11 13 13 4. Section How to clean your machine How to clean the filters How to clean the spray arms How to change the place of your dishwashwer Troubleshooting 14 14 15 7. Section 9. Section Standard and testing information 16 2 EN ! Warnings and Safety Information Electrical safety The dishwasher should be operated under the operating voltage specified. For electrical safety, only earthed plugs and plug sockets should be used. [. . . ] Make sure the electricity and water connections of your dishwasher are in compliance with the instructions for assembly as stated in the relevant part of this manual Any water remaining in the dishwasher after production is carefully removed due to reasons of hygiene. Therefore, always select pre-wash or a programme with pre-wash before first time you use this appliance. Before the first wash, add 1 lt of water in the salt container of your machine If the hardness of the water you use is more than 60°dF (French Hardness) or if you are using pit water, we recommend that you use filters and purifiers. Connections Electricity Information regarding the electrical specifications of your machine is provided on the sticker on the right side of the interior door. If you have to make the connection of your machine to the mains voltage other than stated on the sticker, have a proper transformer connected. If the fuse in your house is less than 16 Amperes, have a 16 Ampere-fuse connected by a qualified electrician. Always call the authorized service whenever you want to change the mains cable of your machine. 6 EN Connection Water Connection Water inlet hose connection 3/4 min 10 There are two different types of water inlet hoses: -Cold water inlet hose (up to 25°C) - Hot water inlet hose (up to 60°C) please check which one is applicable to your model. If you are willing to connect your machine to natural energy resources or to the central hot water supply, first check out whether your water inlet hose type is suitable by checking the temperature values written on the hose. If your hose is not suitable, apply to your authorized service to change the hose. 3/4 1/2 CH DK S 3/4 The water inlet hose is directly connected to the tap. The water pressure coming from the tap must be minimum 0. 3 and maximum 10 bars. Please turn on the tap and check for leakages after connecting the hose. For safety reasons (if your machine does not have the watersafe feature. ) Please ensure the tap is turned off when the machine is not used; For models with AQUABLOCK , N SF 3/4 min 10 If the water connection is made properly, this system shall protect your house against floods. The plastic frame of AQUABLOCK water intake system has electrical components. Appliance should be connected to the water mains with the new hose set. The hose set of the previous machine (if there is any) should be removed 7 EN Connections Drain hose connection Fit the drainage hose of your machine to the drainage pipe without bending. If the length of the hose is not sufficient, apply to the authorized service for an extension made from the same material as the original. Remember that the length of the hose should not exceed 4 meters even when with an extension. the dishes will not be cleaned properly Secure your hose firmly to the drainage pipe to avoid it coming off during the washing process. max 1100 min 500 min 120 Usage Information Water Softener Water Hardness The dishwasher requires lime free water. Your dishwasher has a special water softening system to remove the hardness of the water (Water softener). 8 EN Usage Information Filling in the Water softener Only use special pelletized dishwasher salt in your machine to soften the hard water. Never use other types of salts including table salt, animal feeding salt, sea salt, culinary salt. These types of salt do not dissolve in water easily and will damage your appliance beyond repair. When you run the dishwasher, the Water softener will be full of water. Therefore, adding softening salt should always be done immediately before you start the dishwasher. [. . . ] Reinsert the spray arm back into its original position How to change the place of your dishwasher Empty your machine and shut the water intake valve. Disconnect all other hoses/cables that may prevent the movement of your machine. Please keep the machine upright or laying on its back during carriage to prevent water getting into the control panel. Getting water into the control panel may cause product failure. 15 EN ? Troubleshooting Before calling your nearest service centre check the following: ? Is the machine connected to the mains supply Is the fuse in the mains plug has not blown. [. . . ]