User manual DE DIETRICH DTI709X

[. . . ] Ensure that all control knobs are in the OFF position when not in use. Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance. If the appliance is out of order, disconnect it from the electric supply. · People Safety · This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. [. . . ] After lighting the flame, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. 1 lett. D)to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. 3 If you cannot light the flame even after several attempts, check the "cap" (Fig. In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. Always turn the flame down or put it out before taking the pans off the burner. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if overheated. If the burner does not light even after 15 seconds, release the control knob, turn it the "off" position and wait for at least one minute before trying to light the burner again. If the burner accidentally goes out, turn the control knob to the "off" position and wait for at least 1 minute before trying to light the burner again. 1 A B C A - Burner cap B - Burner crown C - Ignition candle D - Thermocouple D Burner Ultra-Rapid minimum diameter 180 mm. maximum diameter 260 mm. Energy saving advices To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. · Use only pans or pots with flat bottom. Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Screw the parts without forcing, adjust the connection in the required direction and tighten everything. D Fig. 2 A) B) C) D) Ramp with ending nut Seal Adjustable connection Rubber pipe holder for LPG Connection using flexible non metal pipes When the connection can be easily inspected in its full extent, there is the chance to use a flexible pipe according to the rules in force. The flexible pipe must be tightly fixed using clamps according to the rules in force. The flexible pipe should be made ready for use in such a way that: - nowhere it can reach overtemperature, other than room temperature, higher than 30°C; if the flexible pipe, to reach the cock, must run behind the range, it must be installed as shown in Fig. 2; - it is no longer than 1500 mm; - it shows no throttles; - it is not subject to traction or torsion; - it doesn't get in touch with cutting edges or corners; - it can be easily inspected in order to check its condition. The control of preservation of the flexible pipe consists in checking that: - it doesn't show cracks, cuts, marks of burnings both on the end parts and on its full extent; - the material is not hardened, but shows its normal elasticity; - the fastening clamps are not rusted; - expiry term is not due. If one or more abnormalities are seen, do not repair the pipe, but replace it. FO 0067 Important Once installation is complete, check the perfect seal of every pipe fitting, using a soapy solution, never a flame 7 Electrical Connection The appliance is designed to be connected to 220 / 240 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. check that the main fuse and the domestic installation can support the load (see the rating label); 2. check that the power supply is properly earthed in compliance with the current rules; 3. check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. [. . . ] The traction of the screws is able to trace the sealing, any excess of which can then be easily removed. 490 55 27 0 40÷50 240 550 M 140 591 Fig. 9 If several 30cm hob are to be installed side by side into the same cut out, an assembly kit including a support side bracket and supplementary sealings is available at our After Sales Centres. The relevant installation instructions are supplied within the kit package. a FO 0199 a) sealing Fig. 10 30 11 IN Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. [. . . ]