User manual DE DIETRICH DTI702X

[. . . ] INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD; ALL OTHER USES ARE CONSIDERED IMPROPER. DO NOT USE THIS APPLIANCE FOR HEATING ROOMS. DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT. [. . . ] The special pan stand H is for use with woks. The burner controlled by each knob is shown next to the knob. Simply press the knob and turn it anti-clockwise to the maximum flame symbol, until the burner lights. If it does not light in the first 15 seconds, position the knob on 0 and wait at least 60 seconds before trying to light it again. On valved models, once the burner is lit, keep the knob pressed for a few seconds to give the thermocouple time to heat up. The burner may go out when the knob is released: in this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation keeping the knob pressed for a longer time. This is not necessary on burners that are not equipped with thermocouple. Always check that the control knobs are in the (off) position when you finish using the hob. If the burners should go out accidentally, after about 20 seconds a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. In this case, turn the knob to the OFF position and wait at least 60 seconds before trying to light the burner again. 27 Instructions for the user 6. 2 Practical tips for using the burners For better burner efficiency and to minimise gas consumption, use pans with a flat, smooth base and a lid that have a suitable size for the burner, thus avoiding that the flames reach the sides of the pan (see point "6. 3 Pan diameters"). Once the contents come to the boil, turn down the flame far enough to prevent the liquid from boiling over. Once the hob is fixed in position remove excess material using a cutter. 30 Instructions for the installer To fix the hob solidly to the counter top use the 10 supplied brackets, tightening their screws to lock the product firmly in position. The following figures show how to attach these brackets to the lower casing of the product. This appliance can also be installed in a 90 cm base. To fit the brackets the hob must be inserted into the opening made in the counter top, with the edge resting on the actual top. To bracket the hob laterally, just fix the two "L" brackets to the sides of the unit (A) using the supplied screws (1) making sure to align the slot (B) on the bracket with the rivet (C) on the bottom of the product. Stabilise the fixing of the hob by tightening the screw (2) in the rivet (C). Complete the bracketing of the front and rear part of the hob as described in the previous point. 31 Instructions for the installer 8. 1. 2 Fixing to the electric model support structure Create an opening in the counter top with the dimensions shown in the figure, keeping a minimum distance of 50 mm from the rear edge. The lower part of the casing must be fully accessible after the appliance has been installed. This appliance can be mounted against walls higher than the work surface on condition that a distance of "X" be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. 1) between the hob and any shelf that may be installed directly above it. This type of appliance also requires milling to a depth of 3 mm on the counter top with the dimensions shown in figure 2 (detail A). Before positioning the hob, the supplied adhesive sponge "E" (fig. [. . . ] In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described below. 10. 1 Replacement of nozzles on the cooker hob 1 2 3 Extract the grids and remove all the caps and flame-spreader crowns; Unscrew the burner nozzles with a 7 mm socket wrench; Replace the burner nozzles according to the type of gas to be used (see point "10. 2 Burner and nozzle characteristics table"). The nozzles for using town gas (G110 ­ 8 mbar) are available from authorised service centres. 38 Instructions for the installer 10. 2 Burner and nozzle characteristics table RATED Burner HEATING CAPACITY LIQUID GAS ­ G30/G31 28/37 mbar Nozzle diameter 1/100 mm Reduced flowrate (W) 400 800 400 1600 (KW) By-pass 1/100 mm 30 42 30 63 Flowrate g/h G30 76 182 65 262 Flowrate g/h G31 75 179 64 257 Auxiliary (1) Rapid (2) Ultra-rapid int. (4) Burner 1. 05 2. 5 0. 9 3. 6 RATED HEATING CAPACITY 50 79 46 68+68 NATURAL GAS ­ G20 20 mbar Nozzle diameter 1/100 mm Reduced flowrate (W) 400 800 400 1600 (KW) Auxiliary (1) Rapid (2) Ultra-rapid int. [. . . ]