User manual DE DIETRICH DTI 1127 X

[. . . ] We hope you are extremely satisfied with this new appliance and will be happy to receive your suggestions and to answer your questions. Please contact our customer service department or use our Internet site. 72 39 EN 1 / USER NOTICES Keep this user guide with your appliance. If the appliance is ever sold or transferred to another person, ensure that the new owner receives this user guide. [. . . ] € Gas supplied by tank or cylinder (butane/propane) For your safety, you must choose from the three following connection options: — Use rigid copper pipe with screw-on mechanical connectors (G1/2 gas standard mark). € Use a flexible metal hose (stainless steel) with screw-on mechanical connectors (compliant with the NF D 36-125 standard) with an unlimited guarantee (Fig. Refer to the section “Connecting to the electricity supply”. 01 Within the following 5 seconds, — Press touch control twice (Fig. 04 — To change the gas supply type, use the “power slider”, sliding your finger to the left or to the right. Cat: I2H Hourly flow rate below: 25 mbar at 15°C under 1013 mbar Butane G30 Propane G31 FR-CH ES-IT PT-CY EE - PL LT Natural Gas G20 FR Natural Gas G25 28-30 mbar 37mbar 20 mbar 25 mbar FAST BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (kW) Hourly rate (g/h) Hourly rate (l/h) HIGH SPEED BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (kW) Hourly rate (g/h) Hourly rate (l/h) SEMI-FAST BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (kW) Hourly rate (g/h) Hourly rate (l/h) AUXILIARY BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (kW) Hourly rate (g/h) Hourly rate (l/h) HOB WITH 4 GAS BURNERS AND HIGH SPEED BURNER Total heat release rate (kW) Maximum rate (g/h) (l/h) HOB WITH 2 GAS BURNERS AND 2 INDUCTION ZONES Total heat release rate (kW) Maximum rate (g/h) (l/h) 7R 2. 60 438 52 2 / INSTALLING YOUR APPLIANCE EN • Identifying the injectors The adjacent table shows where the injectors are positioned on your appliance according to the type of gas used. 10 kW* diameter 210 = 3100 W diameter 160 = 2000 W *Power obtained with natural gas G20 54 3 / USING YOUR APPLIANCE EN • USING A COOKING ZONE — Place your cookware on the cooking zone. 01 Indicator light — Setting the power: either by sliding your finger on the power slider from left to right to increase power (Fig. 02 You can decrease the power by sliding your finger from right to left (Fig. € Moving your finger slowly allows you to adjust the power more accurately than when you move it quickly. 01 — Set the new power level by sliding your finger to the left or right on the power slider as desired (Fig. You can select between 6 and 9 A beep will confirm your action after a few moments. 02 60 3 / USING YOUR APPLIANCE EN • CHILD SAFETY This function allows you to lock your hob when it is shut off or when it is cooking. € In “locked” mode, any action will produce a key symbol on the displays. € If you activate the lock while cooking, turning off the zones will take priority over the lock. € CLEAN LOCK This function allows you to temporarily lock your hob while cleaning. € To activate CLEAN LOCK: — Your cooking hob must be turned off. 61 EN 3 / USING YOUR APPLIANCE • OPERATING SAFETY • GENERAL STOP — You can stop any gas burners currently operating by pressing touch control . € AUTO-STOP SYSTEM — Should you forget that cooking is in progress, this safety function will automatically turn the hob off after a predefined time (between 1 and 8 hours depending on the power setting). € TEMPERATURE LIMITER (MODEL DTI1127*) — Each cooking zone is equipped with a safety sensor that constantly monitors the temperature of the bottom of the cookware. If you leave empty cookware on a zone which is turned on, the power will be automatically limited to prevent damage to the cookware or hob. [. . . ] ž This is the procedure for connecting your hob to the electric power. Is displayed on the timer , followed by numbers then the display is cleared. ž You are not able to operate any of the controls and the displays show nothing. ž displays E4 and one of the indicator lights for the faulty burner comes on for a few seconds then goes off. [. . . ]