User manual DE DIETRICH DTG1138X

[. . . ] 33 EN EN ES 02 34 66 Dear Customer, When you discover De Dietrich products you experience feelings that only PT 102 DE 134 objects of value can arouse. The quality of the design is illustrated by its timelessness, degree of refinement and elegance, and high standard of finish, resulting in perfect harmony between different appliances. De Dietrich design makes the most of sturdy and noble materials; priority is given to authenticity. By combining the most advanced technologies with the best materials, De Dietrich makes products of the highest quality for the benefit of all those who love cooking. [. . . ] € Turn the wrench clockwise until the line appears on the opposite side(Fig. 02 ➍ Connect the power cable from your hob to your single-phase mains supply (220240 V ). Refer to the section “Connecting to ~ the electricity supply”. Note 48 2 / INSTALLING YOUR APPLIANCE EN • CHANGING THE GAS SUPPLY (CONTINUED) • Switching from butane/ propane gas to natural gas For the 1-burner hob (high-power burner) CHANGE THE INJECTORS, proceeding as follows: — Take off the grill, the cap, and the head of the burner. € Unscrew the central injector located at the base of the burner unit Using a No. 7 spanner, unscrew the 3 injectors located around the central injector (see B ) (Fig. € Replace with the new gas injectors; refer to the injector positioning markers and the gas settings table at the end of this chapter. The new injectors should be fitted as follows: — First, screw them in manually until hand tight. € Connect the power cable from your hob to your single-phase mains supply (220-240 V ). ~ Refer to the section “Connecting to the electricity supply”. Tip - Each time you change the gas supply, tick the box corresponding to the gas level on the label found in the plastic bag. See “Connecting to gas the supply” Note YOUR HOB IS NOW READY TO BE USED WITH BUTANE/PROPANE. Cat : I2H Hourly flow rate below: at 15°C below 1013 mbars TREE-RING BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (kW) Hourly rate (g/h) Hourly rate (l/h) AUXILIARY BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (with safety device) (kW) Hourly rate (g/h) Hourly rate (l/h) TOTAL BURNER 2 38 CM GAS BURNER HOB WITH THREE-RING AND AUXILIARY BURNERS Butane G30 28-30 mbar Propane G31 37mbar Natural gas G25 25 mbar 90A 3. 35 414 482 Hob with 1 high-power burner DTG1138X* HIGH POWER BURNER CENTRAL BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (with safety device) (kW) Hourly rate (g/h) Hourly rate (l/h) HIGH POWER BURNER TOTAL BURNER Marking on injector Nominal heat release rate (kW) Reduced heat release rate (with safety device) (kW) Hourly rate (g/h) Hourly rate (l/h) 49B 1. 850 659 51 EN 2 / INSTALLING YOUR APPLIANCE The table below shows where the injectors can be found on your appliance, according to the type of gas used. 63 Example: injector marking 63 MARKINGS ON THE INJECTORS 38 cm hob with auxiliary burner + triple ring burner Natural Gas Butane/ Propane Gas 90A 45 45A 63 38 cm hob with high-power burner Natural Gas 97B 74B 97B 97B Butane/Propane Gas 63B 49B 63B 63B 52 3 / USING YOUR APPLIANCE EN • DESCRIPTION OF YOUR HOB 2-gas burner model with electronic controls (DTG 1138*) B A 1 high-power gas burner model with electronic controls (DTG 1008*) C A B C Auxiliary burner 0. 53 EN 3 /USING YOUR APPLIANCE • DESCRIPTION OF THE CONTROLS (2-burner model DTG1138*) A A B C B On/off touch controls C Power level touch control Timer touch controls • LIGHTING THE GAS BURNERS To use a function touch control. Place your finger squarely on the chosen touch control until the display shows the new setting. If you do not select a power level, the cooking zone will automatically switch off. B • TURNING OFF Press touch control for the zone you want to use or power touch control until 0 is displayed. A • ADJUSTING THE POWER LEVEL Press touch control or to adjust your power level between 1 and 9. When the appliance is switched on, you can move directly to maximum power by pressing touch control or to minimum power with touch control . [. . . ] ž displays E4 and one of the indicator lights for the faulty burner comes on for a few seconds then goes off. In all cases, check the following: The display of an error code automatically blocks the use of the timer 61 ➤ displays D2. ž displays E2 and one of the ring’s indicator lights is flashing. ž displays E7: one of the indicators lights up to say the burner is faulty. [. . . ]