User manual DE DIETRICH DRN1027IS

[. . . ] Blk 1093, Lower Delta Road #04-05 Tiong Bahru Industrial Estate Singapore 169204 support@hauppauge. com. sg Tech Support: (+65) 276 4412 Telephone: (+65) 276 9163 Fax: (+65) 276 9167 www. hauppauge. com. sg . M2TS: this is an H. 264 format which can be played on a Sony Playstation3. You create this format when you click on Playstation3 in Arcsoft Capture. Internet addresses: Sales: sales@hauppauge. com Tech Support: techsupport@hauppauge. com Web site: www. hauppauge. com Audio connection Audio from the set top box is connected where you have connected the video input: either to the optical audio in (rear), RCA audio in (rear) or RCA audio in (front). Optical audio is connected on the rear panel. Included with HD PVR: · · · · · · · HD PVR H. 264 high definition video recorder, USB Component video cable set, 1 meter Audio cable set USB cable 5v 2 amp power supply IR Blaster transmitter cable to control the channel changing on your cable TV or satellite set top box HD PVR Installation CD, with HD PVR drivers for Windows and Arcsort Total Media Extreme USB connection Plug one end (the square end) of the supplied USB cable into the HD PVR's USB cable connector. HD PVR is compatible with USB 2. 0 (high speed) USB only. Step 2: Boot your PC Step 3: Plug the power supply into HD PVR After your PC has booted to Windows, plug the supplied Power Supply into the Power input on HD PVR. [. . . ] HD PVR is compatible with USB 2. 0 (high speed) USB only. Step 2: Boot your PC Step 3: Plug the power supply into HD PVR After your PC has booted to Windows, plug the supplied Power Supply into the Power input on HD PVR. The power supply is 5VDC@ 2amps. Step 4: Install the HD PVR Windows driver and applications ote: the HD PVR needs to be powered up in this step and plugged into your PC while the Windows drivers are installed. N Turn on your PC, and boot into Windows. If a 'Found New Hardware' wizard appears, please cancel it and allow windows to load fully before proceeding. Insert the WinTV Installation CD-ROM in your PC's CD-ROM drive. entitled Configuring the IR Blaster. Running Arcsoft TotalMedia Extreme To start the ArcSoft Total Media Extreme application, double click on the TotalMedia Extreme icon on your desktop. N ote: if the CD does not autorun, navigate to the CD and run the 'Setup. exe' file. "Hauppauge WinTV Installation CD-ROM" window will appear on the screen. Install the HD PVR driver Click the button labeled Step 1: Install Drivers. A blue screen will open and begin installing the drivers for your WinTV. Once the drivers have installed, click on the Finish bar to exit. Install the HD PVR application Click the button labeled Step 2: Install software Choose a language, and click next, click Install. The Arcsoft Total Media Extreme software application, HD PVR Scheduler application, and IR Blaster application will be installed. The program will open to this initial screen which has four icons along the top. Recording Videos Click on the video cassette icon to open the Arcsoft Capture Module recording function. Make sure the Source is set to Hauppauge HD PVR Capture. Playing back your video recordings To play back a file, close the Arcsoft Capture Module recording window and click on the Play Video icon. Select your A/V input source Choose the Video and Audio inputs you are using to setup up the recording: If you are using Component video from your set top box, choose Component. If you are using S-Video or Composite video from your set top box, choose S-Video or Composite. ote: if you are connecting HD PVR to a game console, make sure the Component video output of the game console is set to 1080i. N N ote: the latest driver updates are available at: www. hauppauge. com in the Support section. Step 6: Install the IR Blaster cable (optional for use with a cable TV or satellite receiver box) Plug in the IR blaster cable: plug the jack at the end of the IR RemoteBlaster cable into the IR receiver jack on the HD PVR. Install the IR transmitter (blaster) at your set top box: Attach the end of the IR transmitter over the remote sensor on the set top box to be controlled. If you have made HD recordings at 5Mbits/sec, this disk will hold about 110 minutes of video. To add videos to the DVD layout Click the Get Media tab. Click on the Video button to add a recording you have previously made. Click on Capture Video to capture a new video to the hard disk for editing and burning. When the conversion process completes, it will display the results. Utilities: Arcsoft Media Converter Click the Utilities option from the main menu, then choose Arcsoft MediaConverter Configuring the IR Blaster The IR Blaster lets the HD PVR change the channel on a satellite or cable TV set top box by transmitting `channel change' commands to the box via an Infra Red (IR) transmitter. The IR cable jack plugs into the back of the HD PVR, and the IR transmitter needs to be positioned over the IR receiver on your set top box using the self stick tape supplied on the front of the transmitter. IR Blaster Config program (BlasterCfg. EXE) for configuring the codes for the IR transmitter. Learning a new set top box remote control code If you have a set top box that is not part of the Hauppauge IR Blaster preset codes and the Scan function does not work, you can add a new set top box by using the Learn function. To access the learn function, click on Advanced config, and then click Learn. To learn the new keys: hold the remote control from your set top box as close to the IR receiver and learn sensor as possible. a 45 degree angle, as seen above is helpful in the Blaster Configuration program, click the button you would like to learn (for example: 1) then depress and hold the corresponding key on your set top box remote control. You will be instructed in the message box when to release the key on your remote control. [. . . ] a 45 degree angle, as seen above is helpful in the Blaster Configuration program, click the button you would like to learn (for example: 1) then depress and hold the corresponding key on your set top box remote control. You will be instructed in the message box when to release the key on your remote control. Do this for the keys 0 to 9 plus On and Enter Key numbers For best results, the remote control can touch the HD PVR plastic case at a 45 degree angle Using the WinTV Scheduler The WinTV Scheduler can be used to control the channel changing of a set top box for cable or satellite. 2. During the installation of the HD PVR software from the Installation CDROM, the Hauppauge IR Blaster applications will be automatically installed. You will be asked during the IR software installation to acknowledge a software license. Configuring the IR Blaster The IR Blaster Configuration program can be found in the Program Groups / Hauppauge WinTV. [. . . ]