User manual DE DIETRICH DPE7729XF

[. . . ] Short title or reference to the measurement and calculation methods used to establish compliance with the above requirements. The performance of each individual burner is calculated according to standard EN 30-2-1 + A1:2003 + A2:2005 The total efficiency of the hob is calculated according to the EU Regulation 66/2014 Par. 2 The efficiency is calculated only for the burners with a nominal capacity exceeding 1, 16 KW ( EN 30-2-1 + A1:2003 + A2:2005; Par. 1) Information which is relevant to the customer to minimize the energy consumption during usage: Energy Saving Tips: use pots having flat base, Use pots with proper size, use pots with lid, minimize the amount of liquid or fat, when liquid starts boiling reduce the setting. [. . . ] Make a note of the references of your appliance on the "After-Sales Service and Customer Relations" page so that you can readily find them in future (6. 1•1 - FITTING : This worktop must be at least 3 cm thick and heatresistant or else coated with a heat resistant material. Any possible wall unit over the cook-top must be placed at a distance of at least 760 mm from the top. It is advisable to isolate the appliance from the piece of furniture below with a separator, leaving a depression space of at least 10 mm (1. If the hob is going to be installed on the top of an oven, precautions must be taken to guarantee an installation in accordance with current accident prevention standards. Under no circumstances keep any sprays or pressurised containers in any compartment below the hob (see "Safety guidelines“ chapter). €¢ Remove the "pan supports", burner caps and burner heads, noting their original positions. €¢ Turn the hob upside down and place 7 •1 INSTALLATION 1•3 - GAS CONNECTION: If the hob is to be installed above an oven or if other nearby heating appliances could heat and damage the gas hose, then it is essential that a rigid pipe is installed instead. If a flexible hose is used (as is the case of butane gas) then it must not be installed in a place where it may be in contact with a moving part of the kitchen unit or a location likely to get cluttered. No flexible hoses with a limited service life may be longer than 2 metres and must be accessible for inspection along their entire length. Whatever means of connection is chosen, make sure that it is gastight when installed, using soapy-water. The gas connection must comply with the regulations in force in the country where it is installed. Cross section of the cable to be used 220-240 V˜ - 50 HZ gas Cable H05RR-F - T90 Cross section of conductors in mm² Two conductors, One of which is an earth 0, 75 The protective conductor (green/ yellow) is connected to the earth terminal on the hob and must also be connected to the installation's earth terminal (1. If the supply cable is damaged, it must be replaced by a cable or special set available from the manufacturer or its after-sales department. So that you can find the references for your appliance without difficulty in the future, we recommend that you make a note of them on page (6. 1) "After-sales service and customer relations“ (that page also tells you where to find them on your appliance). 8 •1 INSTALLATION In an existing installation, a flexible hose fitted C with jubilee clips (in conformity with the local regulations). In this case an end connector must be used with a sealing washer A fitted between the end connector B and the elbow on the hob. Yo u c a n p u r c h a s e t h e e n d connector and the sealing washer from your after-sales department. 1•4 - CHANGING THE TYPE OF GAS: Your appliance is supplied ready for use with natural gas. The injectors required for adapting it to butane/propane can be found in the plastic bag containing this guide. Whenever you change the gas type, you must follow these steps in turn: 1. [. . . ] €¢ The 2 reference cuts must be entered on the 2 references made on the flame retardant. 3 WHEN LIGHTING, FLAMES IGNITE BUT GO OUT WHEN THE KNOB IS RELEASED • Press the knobs as far as they will go and maintain the pressure for several seconds after flames appear. €¢ Check that the burner components are correctly positioned. €¢ Check that the sealing washers under the knobs have not come out of their locations. [. . . ]