User manual DE DIETRICH DOS1045X

[. . . ] -- This appliance is not intended for use by people with (including children) impaired physical, sensorial or mental abilities, or people lacking in knowledge or experience, unless they receive prior supervision or instructions on using the appliances through a person responsible for their safety. -- When you receive the appliance, unpack it or have it unpacked immediately. Make note of any concerns or reservations on the delivery slip and make sure to keep a copy of this form. Do not use it for commercial or industrial purposes or for any other purpose than that for which it was designed. [. . . ] If the power cable is damaged, it must be replaced by a cable or a special kit available from the manufacturer or its AfterSales Service Department. 99643561_A_ML. qxp 30/08/2007 13:53 Page 80 EN 2 / INSTALLING YOUR APPLIANCE Warning We cannot be held responsible for any accident or incident resulting from nonexistent, defective or incorrect earthing. If the electrical installation in your residence requires any changes in order to hook up your appliance, call upon a professional electrician. fig. 2 fig. 1 fig. 3 - To reset the time on the clock Press and hold the touch control for a few seconds until the display is flashing (fig. 1), then release. fig. 2 fig. 1 84 99643561_A_ML. qxp 30/08/2007 13:53 Page 85 4 / USING YOUR APPLIANCE EN Instant cooking -- The programmer should display only the time. Press the START (fig. 1) touch control then select the cooking time chosen using the + or - buttons (fig. 2). The shelf support indicator and heating elements in use also light up. Place your dish in the oven based on the recommendation indicated in the display. Your oven recommends the optimal temperature for the chosen cooking mode. It is, however, possible to adjust the temperature by pushing the control touch C (fig. 3). The "C" button flashes in the indicator and tells you that the temperature can be adjusted by pressing the + or - button (fig. 4). The temperature rise indicator is activated and indicates the temperature increase in the oven. A series of beeps will be emitted when the oven reaches the selected temperature. fig. 2 fig. 1 fig. 3 fig. 4 Warning After a cooking cycle, the cooling fan continues to operate for a period of time in order to guarantee optimal oven reliability. Warning All types of cooking are done with the door closed. 85 99643561_A_ML. qxp 30/08/2007 13:53 Page 86 EN 4 / USING YOUR APPLIANCE PROGRAMMED COOKING - Cooking with immediate start and programmed duration - Select the desired cooking mode and adjust the temperature (see paragraph: instant cooking). The display flashes 0:00 to indicate that you can now adjust the setting (fig. 1). fig. 2 fig. 1 After these three steps, the oven heats up: A series of beeps will be emitted when the oven reaches the selected temperature. At the end of cooking (end of programmed time), - the oven stops, - the cooking time indicator and 0:00 both flash (fig. 3), - a series of beeps sounds for a few minutes. The beeps can be definitively stopped by pressing any touch control. fig. 3 86 99643561_A_ML. qxp 30/08/2007 13:53 Page 87 4 / USING YOUR APPLIANCE EN PROGRAMMED COOKING - Cooking with delayed start and chosen cooking end time Proceed as with programmed cooking. - Press the button. The display flashes to indicate that you can now adjust the setting (fig1). fig. 2 fig. 1 After these 3 steps, oven heating is delayed so that cooking ends at 16:00. At the end of cooking (end of programmed time), - the oven stops, - the cooking time indicator and 00:00 both flash (fig. 3), - a series of beeps sounds for a few minutes. The oven cavity is lit when cooking starts and the light switches off at the end of cooking. fig. 3 87 99643561_A_ML. qxp 30/08/2007 13:54 Page 88 EN 4 / USING YOUR APPLIANCE USING THE TIMER FUNCTION - Your oven's programmer can be used as an independent timer that allows you to count down a time without operating the oven. fig. 1 timer symbol and 0m00s flash. - Adjust the chosen time by pressing the touch controls + or - (fig. 2). fig. 2 A series of beeps is emitted when the time is over, these beeps can be stopped by pressing any touch control. Warning It is possible to change or cancel the timer programme at any time by turning it to 0 and validating. 88 99643561_A_ML. qxp 30/08/2007 13:54 Page 89 4 / USING YOUR APPLIANCE EN CUSTOMISING THE RECOMMENDED TEMPERATURE Select the cooking function: - Press the START button. [. . . ] - The oven is not connected or the Plug in your oven or change the fuse. Press and hold down the + and - button for 10 seconds until a beep is emitted. The cooling fan continues to operate after the oven stops. - The fan should work for a maximum of one hour after cooking, or when the oven temperature is greater than 125C. - If it does not stop after 1 hour. The oven is not heating, - Your oven is programmed for a and "DEMO" appears in demonstration. the display intermittently approximately every 8 seconds. Warning - Repairs to your appliance should only be performed by professionals. [. . . ]