User manual DE DIETRICH DOD778X

[. . . ] This could cause damage in case the appliance is inadvertently switched on. Always place the dripping pan in position to collect fat when using the grill or when cooking meat. Pour a little water into the dripping pan to avoid smoke and unpleasant smells. For hygiene and safety reasons, this appliance should be kept clean at all times. [. . . ] Then press button C and while turning knob E enter the end of -+ cooking time. Turn the thermostat and function control knobs to the required settings. The oven temperature light nor oven light will not come on until the oven switches on. When cooking is completed, the "AUTO" -+ signal will flash an audible signal will be heard for approximately 2 minutes. To cancel press button A and return control and thermostat knobs to the OFF position. A U T O A U T O Press button A and while turning knob E enter the required time (maximum 23 h 59 min. ) After required time has been selected the clock will revert to the time of day. When time is up an audible signal will be heard for approximately 2 minutes. To cancel press button A and return control and thermostat knobs to the OFF position. Setting the minute minder -+ i In case of loss of power, all the settings (time of day, setted programs or programs in operation) will be cancelled. When the power is restored, the numbers on the display will flash, and the timer has to be reset. 44 The multifunction oven Conventional cooking Turn the oven function control knob to the relevant symbol ( ) and set the thermostat knob on the required temperature. If you need more heat from the bottom or from the (top heating top, turn the oven function control knob to element only) or (bottom heating element only). temperatures inside the The Fan Oven Turn the oven function control knob to the relevant symbol ( ) and set the thermostat knob on the required temperature. If you need to cook more than one dish in the fan oven at the same time, place the shelves on the first and third position from the bottom (fig. 4). This could affect the enamel brightness, but it will have no consequence on the oven performances. To avoid these stains to be burnt out during the next cooking, carefully clean the oven cavity after all fruits cookings. Fig. 7 FO 0027 The Oven Door and its gasket F Before cleaning the oven door, we recommend you to remove it from the oven. Proceed as follows: a) open the oven door completely; b) find the hinges linking the door to the oven (fig 7); c) unlock and turn the small levers located on the two hinges (fig. 6); d) handle the door by its left- and right-hand sides, then slowly turn it towards the oven until it is halfclosed; e) gently pull the oven door off its site (fig. 6); f) place it on a steady plan; g) unscrew the two screws marked with lett. A fig. 7; h) pull up the oven door glass and take it away from the oven door. Once the cleaning is carried out, refit the oven door, following the procedure in reverse. The correct operation of the oven is ensured by a gasket placed round the edge of the oven cavity. 8 FO 0287 Ensure the electricity supply is switched off before carrying out this operation. The oven bulb has to comply to these features: a) resistant to temperatures of 300 °C; b) electric rate: 230 V - 50 Hz; c) electric power rate: 15 W. ; d) connection type: E 14. [. . . ] When installing an electric plate hob over the oven, the hob's electrical connection and the oven's one have to be carried out separately, for security reasons and to let the oven be taken off the unit easier, if necessary. Electrical Connection Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load; 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. This appliance is delivered without an electric supply cable, therefore, you will have to fit to it a supply cable with standard plug, suitable for the total electric load specified on the rating plate. If connecting the appliance directly to the electric system, a double pole switch must be installed between the appliance and the electricity supply, with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current rules. [. . . ]