User manual DE DIETRICH DME1115W

[. . . ] If you are unsure of any of the information contained in these instructions, please contact the Samsung customer care center. These instructions are only valid for the countries of destination (see page 2 of this booklet). The manufacturer is not responsible for any damage to persons or property caused by incorrect installation or use of the appliance. The appliance is only certified for the countries stated on the appliance. [. . . ] use good-quality oil, such as olive, maize, sunflower or peanut oil when stir-frying. Butter and margarine on the other hand will burn because of the high heat. place the dishes with the longest cooking time in the pan first, so that at the end of the cooking time all ingredients are cooked al dente at the same time. It is normal for the colour of the brass caps to change as a result of high temperature that occur during use of the wok. Use of the wok auxiliary support (GN792 and GN952) The auxiliary support supplied for the wok burner provides additional stability for woks with a round base. Always position the auxiliary support on the wok support at a 45 degree angle (see illustration). If positioned incorrectly, the auxiliary support will get too hot and may become damaged. wrong right GB 14 3. 3 How to turn on Turn on Each burner can be adjusted steplessly between the full and low positions. Burner indication 0-setting High setting Low setting Open the main gas valve (only by first use). Press the control knob and turn it counterclockwise to ignite the burner. Flame failure device The flame failure device ensures that the gas supply shuts off if the flame goes out during the cooking process. Hold the control knob pressed in the high setting for approximately 5 seconds to switch on the flame failure device. Finally dry everything with a clean soft cloth. Top plate Regularly wipe over the top plate using a soft cloth that has been dampened in warm water to which a dash of washing-up liquid has been added. Thoroughly remove salty foods or liquids from the hob as soon as possible to avoid the risk of corrosion. Stainless steel parts of the appliance may become discoloured over time. Clean these parts with a product that is suitable for stainless steel each time the appliance is used. GB 19 3. 6 Cleaning and maintenance Burners Remove the burner caps, burner head and burner ring by pulling them upwards and away from the top plate. Wipe the fixed parts of the burner base with a damp cloth and dry afterwards. Gently wipe the thermocouple and spark plug with a well wrung-out cloth and wipe dry with a clean cloth Make sure that the injector is not blocked before placing the burners back on the top plate. Assemble the auxiliary, semi-rapid, rapid and wok burners as follows Replace the burner head (12) by ensuring that the locating tabs fit into the notches in the burner base (14). 12 14 15 16 11 12 13 14 15 16 Place the burner head (12) on the burner ring (13) so that the thermocouple (15) and the spark plug (16) extend through their respective holes in the burner head. Replace the burner cap (11) by ensuring that the locating tabs fit into the notches in the burner base (14). Replace parts in the correct order after cleaning Do not mix up the top and bottom. Set the pan supports down vertically without sliding them over the spillage well. GB 20 3. 6 Cleaning and maintenance Burners Remove the burner caps, burner head and burner ring by pulling them upwards and away from the top plate. Wipe the fixed parts of the burner base with a damp cloth and dry afterwards. Gently wipe the thermocouple and spark plug with a well wrung-out cloth and wipe dry with a clean cloth Make sure that the injector is not blocked before placing the burners back on the top plate. Assemble the auxiliary, semi-rapid, rapid and wok burners as follows Replace the burner head (12) by ensuring that the locating tabs fit into the notches in the burner base (14). 12 14 15 16 11 12 13 14 15 16 Place the burner head (12) on the burner ring (13) so that the thermocouple (15) and the spark plug (16) extend through their respective holes in the burner head. Replace the burner cap (11) by ensuring that the locating tabs fit into the notches in the burner base (14). Replace parts in the correct order after cleaning Do not mix up the top and bottom. [. . . ] In all cases, the main gas valve for the appliance must be easily accessible. The gas pipe and the connector must not be bent or blocked by any other appliances. Check the dimensions of the appliance as well as the dimensions of the gap to be cut in the kitchen unit. The panels located above the work surface, directly next to the appliance, must be made of non-flammable material. [. . . ]