User manual DE DIETRICH DHG397XP1

[. . . ] Check the data label inside the appliance; if the symbol ( ) is NOT printed, read the following: ATTENTION: This appliance must be earthed. When making the electrical connections, check that the current socket has a ground connection. The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked ], or coloured green or green and yellow; the wire which is coloured with the letter E or by the earth symbol [ blue must be connected to the terminal which is marked with the letter N or coloured black; the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. [. . . ] For the electrical connection, follow all the other instructions on the "Warnings" sheet. Check to see the grease filters have been removed; if necessary, remove these by moving the catch (B) and turning these outwards (Fig. The bottom of the wall unit must have a thickness of between 15 and 20 mm. Fit the appliance in the hole made on the wall unit, first positioning the rear part, so the flap on the back rests on the wall unit; next, slightly slide the appliance back, towards the wall (Fig. Without leaving the appliance, secure this to the wall unit by means of the 4 screws (Fig. Proceed with final fitting, using the 4 screws (the longest ones); See Fig. Use a flexible pipe and lock it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). 8): Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot lamp (S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the corresponding pilot lamp (S) flashes to indicate that the grease filters must be cleaned. To restart the hour counter (RESET), hold the button A pressed down for about 1" (while the pilot lamp S is on). Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down for about 1", the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button C: drives the motor in second speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button D: drives the motor in third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button E: drives the motor in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Pay special attention to the grease filters: the grease filters must be cleaned approximately once every 30 hours of operation (when the light button lamp comes on) - Fig. [. . . ] Om de telling van de uren weer te laten starten (RESET), moet de toets A ongeveer 1" ingedrukt gehouden worden (terwijl het lampje S in werking is). Toets B: schakelt de motor in op de 1e snelheid (het betreffende lampje gaat branden); als hij ongeveer 1" ingedrukt gehouden wordt, gaat de motor uit; door nogmaals op de toets te drukken (terwijl het lampje brandt) wordt de TIMER ingeschakeld, zodat de motor na 5' stopt (het betreffende lampje knippert). Toets C: schakelt de motor in op de 2e snelheid (het betreffende lampje gaat branden); door nogmaals op de toets te drukken (terwijl het lampje brandt) wordt de TIMER ingeschakeld, zodat de motor na 5' stopt (het betreffende lampje knippert). [. . . ]