User manual DE DIETRICH DHD556XE1

[. . . ] Make sure that children do not touch and that they do not treat it as a toy. -- When you receive the appliance, unpack or have it unpacked immediately. Make note of any concerns or reservations on the delivery slip and make sure to keep a copy of this form. Do not use it for commercial or industrial purposes or for any other purpose than that for which it was designed. [. . . ] In this case, you should add an active carbon filter which will keep in odours. 2 51 EN 2 / INSTALLING YOUR APPLIANCE ELECTRICAL CONNECTIONS During installation and maintenance operations, the appliance must be unplugged from the electrical grid; fuses must be cut off or removed. The electrical connections are made before the appliance is installed in its housing. Ensure that: - the electrical installation has sufficient voltage, - the electrical wires are in good condition, - the diameter of the wires complies with the installation requirements. Warning This appliance is delivered with a H 05 VVF power cord that has three0. 75 mm2 conductors (neutral, phase and ground). It must be connected to the main power supply (which should be a 220-240 V single phase current) via a CEI 60083 standardised socket that should remain accessible after installation, in keeping with installation guidelines. We cannot be held responsible for any accident resulting from an inexistent, defective or incorrect ground lead. If the power cable is damaged, call the after-sales service department in order to avoid danger. Warning If the electrical installation at your residence requires any changes in order to hook up your appliance, call upon a professional electrician. Warning If the hood displays any malfunctions, unplug the appliance or remove the fuse corresponding to the electrical socket where your appliance is plugged in. 52 2 / INSTALLING YOUR APPLIANCE EN ASSEMBLING THE HOOD 5mm x2 Warning The hood must be installed in compliance with all applicable regulations concerning the ventilation of premises. In particular, the evacuated air should never be conveyed to a duct used to evacuate smoke from appliances that use gas or other combustible fuels. Unused ducts may only be used after approval from a competent specialist. The minimum distance between the cooking surface and the lowest part of the hood must be 70 cm. If the instructions for the hob installed under the hood specify a distance of more than 70 cm, this requirement must be respected. 1) on the wall that is centred over the cook top and that extends from the horizontal line drawn in the previous step (A) to the ceiling. -- Cut the drilling template by following the dotted lines to obtain two parts, C1 and C2 (fig. 1) on the wall, superimposing the line that represents the hood's axis over vertical line B (fig. 2 Tip Adjust the level of your hood before fully tightening up the four D and E screws. F E fig. In the event that the hood will be operated using outdoor evacuation, you should ensure a sufficient inflow of fresh air to avoid a pressure deficiency in the room. 55 E fig. 3 EN 3 / USING YOUR APPLIANCE DESCRIPTION OF CONTROL PANEL A B C D E F A B C Automatic operation indicator Manual operation indicator D Automatic control or "OFF" control E Saturated cartridge and recycling filter indicator F Manual control Light control and light intensity adjustment Supplying power When power is first supplied to the hood, it is in the OFF position. Tip This Guide to Installation and Use is valid for several models. Minor differences in details and fittings may emerge between your appliance and the descriptions provided. 56 3 / USING YOUR APPLIANCE EN SELECTION OF HOB TYPE To select your hob type, place the hood in the OFF position by briefly pressing the control. Then simultaneously press on and . Briefly press the control again so that the appropriate number of indicators are lit to reflect your hob type. Refer to the table below: Induction hob Ceramic hob Gas hob Induction/gas hob Hob with cast iron burners Induction/ceramic hob To confirm your type of hob, press and hold the control until the three indicator lights go out. 57 EN 3 / USING YOUR APPLIANCE LIGHT Briefly press to light your hood's lamp. It is possible to modify the intensity of the light by continuing to press on . SWITCHING TO AUTOMATIC MODE Press and hold the control. The "Auto" indicator flashes to tell you that the hood is in automatic mode. SWITCHING TO MANUAL MODE The manual mode makes it possible to manually select the suction speed of your hood from 1 to 5. Each additional brief depression on the control increases the speed from 1 to 5 and a final depression of the control returns to speed 1. 58 3 / USING YOUR APPLIANCE EN IMMEDIATE STOP IN MANUAL MODE To stop the hood when it is in manual mode, briefly press the control. [. . . ] In the event of tough stains, use a non-abrasive cream, then rinse with clean water. This filter traps odours and must be changed at least once a year depending on your level of use. You should order these filters from your dealer (quoting the reference shown on the identification plate located inside the hood) and note the date the filter was changed. Use a commercial household cleaning product then rinse abundantly and dry. [. . . ]