User manual DE DIETRICH DHD479XE1

[. . . ] Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. [PC] !' [ DVI] !' [ AV] !' [ Component] !' [ [DisplayPort] !' [MagicInfo] !' [TV] Note · The [RGB/COMPONENT IN] port is compatible with RGB (PC) and Component signals. HDMI1] !' [ HDMI2] !' Introduction However, the picture may display abnormally if the connected external input signal is different from the selected video signal. [. . . ] You can purchase the locking device from an electronics store, an online shop, or our service Center. · Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally. Introduction Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. POWER OFF Number Buttons DEL + VOL SOURCE D. MENU TOOLS Up-Down Left-Right buttons INFO The Color button and the PC/DVI/HDMI/DP selection button. TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo POWER OFF Number Buttons Turns the product On/Off. Used to enter the password during the OSD adjustment or to use MagicInfo. DEL / GUIDE button The "-" button is used to select Digital channels. / GUIDE button Introduction Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time. D. MENU DTV menu display Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Up-Down Left-Right buttons INFO The Color button and the PC/DVI/HDMI/DP selection button. Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Current picture information is displayed on the upper left corner of the screen. In TV mode, these buttons can be used to configure a list of channels. 4. Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connecting Using a HDMI Cable 1. 2. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Note In HDMI mode, only PCM format audio is supported. Connections Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the LCD Display. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Connecting a DVD Player Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Connections Note · · · · Press SOURCE on the product or remote control and select "Component". If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. (They may cause flaws or deformation of the screen surface. ) · The user is responsible for any damage caused by using these substances. Symptoms and recomended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor Coloring, become noisy, etc. [. . . ] Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: A: "No signal" message. Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Ensure that the PC or video sources are turned on. [. . . ]