User manual DE DIETRICH DCM1000X

[. . . ] A), changer l'injecteur (voir figure B) et le remplacer avec celui approprié au nouveau type de gaz (voir tableau D). Using your appliance in complete safety Our research teams have designed a new generation of kitchen As a result of our unique expertise, we have produced A range of goods whose quality, design and technical advance are unsurpassed. You will find that the clean lines and modern look of your DE DIETRICH appliance blends in perfectly with your kitchen It is easy to use and performs to a high standard. DE DIETRICH also makes a range of products that will enhance Use of the electric oven There are models to complement your new DE Of course, we make every effort to ensure that our products meet all your requirements, and our Customer Relations department is at your disposal, to answer all your questions and to listen to all your suggestions (see back cover of manual). [. . . ] A special valve for routinely turning the gas supply on/off must be installed between the gas inlet tube to the room and the hob, in order to cut off the gas supply after cooking in the event of accidents during cooking. This valve must be easily accessible at all times and should be closed during long periods of no use. The gas tube must be routed in such a way that it is not fed through hot areas and does not come into contact with any hot parts of the appliance, e. Tube installation must be carried out in such a way as to ensure that it runs freely and that it cannot come into contact with or be bent by any movable parts in the kitchen, e. Certain types of cookers can be set for sypply both on the right and lefthand side. In this case it is sufficient to reverse the position of the cad nipple reducer. Conversion to LPG Always isolate the cooker from the electricity supply, turn off the gas supply temporarily and proceed as follows. REPLACEMENT OF WORK-TOP INJECTORS In order to change the work-top injectors, it is necessary to act as follows: remove the grids, remove burners and flame-spreaders (see fig. B) and replace it with another one suitable for the new type of gas (see table D). Reassemble everything in the opposite direction, paying attention to place the flame-spreader in the right way on the burner. MINIMUM FLOW ADJUSTMENT FOR WORK-TOP TAPS In order to adjust the minimum, act as follows: switch the burner on, and turn the knob towards the minimum flow position . Remove the knob from the tap, introduce a little screwdriver in the tap rod (fig. Attention: in taps with security valve, the minimum adjusting screw Z is placed outside the rod tap (fig. This appliance must be installed by a qualified person in accordance with the latest edition of the IEE Regulations and in compliance with the manufacturer instructions. Ensure that the voltage is the same as that stated on the rating plate. The rating plate which can be found on the inside of the front appliance drawer. If an fixed appliance is not equipped with supply cable and plug, the power supply must be fitted with a disconnect switch in which the distance between contacts permits total disconnection in accordance with overvoltage category III, as required by installation regulations. Be sure that the earth wire green/yellow is not interrupted by the switch Cable type HO5 RRF 3 X 1. 5 mm2 Connecting the mains cable Open the mains terminal block cover as shown, unscrew screw A the cable clamp and unscrew (not fully) the screws in the mains terminal block L N E which secure the three wires of the mains cable. Allow sufficient cable length for the cooker to be pulled out for cleaning, but do not let it hang closer than 50mm (2) to the floor. Keeping the knob pressed, the electric automatic ignition of the burner will be started up. Hold the knob in for around 10 seconds once the flame has ignited to allow the thermocouple to heat up. [. . . ] Setting error A setting error is made if the time of day on the clock falls within the cooking start and end times. To correct the setting error, change the cooking time or cooking end time. Cancelling a setting To cancel a setting, press the cooking time button a nd then press the - button until 00 00 appears on the display. Before cleaning the appliance, disconnect the gas general tap and unplug the appliance or disconnect power at the main circuit breaker of the electrical system. [. . . ]