User manual CME CONTROL 2 PLUS

[. . . ] · Make a note of the codes for your TV and VCR on the adhesive label inside the battery cover. This note will be handy if you have to reprogram your control. SET-UP Read these instructions carefully before programming your remote control!To program the CONTROL 2 Plus remote control, follow the indications in section A , B or C . A BRAND SEARCH PROGRAMMING MODE Warning: program one appliance at a time. 1. In the code book enclosed, look for the brand of your appliance and make a note of the code indicated at the side (e. g. [. . . ] TV VCR Press and release the TV or VCR selection key for the appliance you want to use. Hold down the SHIFT and ON/OFF keys together until the TV or VCR selection key starts to flash indicating that the remote control is in programming mode. 1 0 3 5. If not, try the code entry procedure again from point 3. B DIRECT CODE ENTRY FOR REMOTE CONTROLS VERSIONS V5 - V6 Warning: program one appliance at a time. 1. In the code book enclosed, look for the brand of the TV or VCR appliance you want to control and make a note of the first code in the list BENEATH the brand previously identified (e. g. TV VCR Press and release the TV or VCR selection key for the appliance you want to use. You cannot set a VCR code using the TV key. Additional check Point the remote control at the TV or VCR. If there is no response or the appliance only responds partially or incorrectly, it is probable that you have used the wrong code. Make a note of the TV and VCR codes used to program the remote control on the adhesive label inside of the battery cover for rapid consultation. The remote control leaves the programming mode and the TV or VCR selection key stops flashing: · if no keys are pressed for 15 seconds · if an invalid brand code is entered · if you press the TV - VCR - F1 - F2 - F3 - F4 keys by mistake. 4. Hold down the SHIFT and ON/OFF keys together until the TV or VCR selection key starts to flash indicating that the remote control is in programming mode. 8 0 7 5 5. Within the next 15 seconds, key in the three figure code you noted previously (e. g. If not, try the code entry procedure again from point 3. C GLOBAL SEARCH REMOTE CONTROL PROGRAMMING This operation may take up to about 20 minutes. TV VCR Press and release the TV or VCR selection key for the appliance you want to use. ­ the TV key is used to search only for the TVs of the brand selected ­ the VCR key is used to search only for the VCRs of the brand selected. Additional check Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar but different remote control. Hold down the SHIFT and ON/OFF keys together until the TV or VCR selection key starts to flash indicating that the remote control is in programming mode. 0 0 0 4. The TV or VCR selection key flashes more quickly to indicate that the remote control is ready for the search. Press and release slowly one of the most frequently used keys several times STOPPING when the appliance responds correctly to the command. Three flashes indicate that the operation has been completed correctly. Identify and make a note of the code for the appliance which you have searched for, following the code noting procedure (see "NOTING THE PROGRAMMED CODE" section). NOTE: THE TV OR VCR SELECTION KEY STOPS FLASHING. The remote control leaves the programming mode and the TV or VCR selection key stops flashing: · if no keys are pressed for 15 seconds · if the code search list is completed. · if you press the TV - VCR - F1 - F2 F3 - F4 keys by mistake. NOTING THE PROGRAMMED CODE Always write down the 3-digit code for your remote control on the label inside the battery cover after running the search and saving the code. This may be useful if you need to reprogram your remote control in the event of accidental cancellation or when you change used batteries. [. . . ] Locate the additional function you require and note down the symbol or number which appears below it. From now on, whenever you press F1, the additional command just saved is transmitted to the appliance and stops when F1 is released. NOTE: If the TV or VCR selection key does not flash, repeat the saving procedure described above. TROUBLESHOOTING PROBLEM The appliance does not respond and the TV and VCR selection keys do not light up when you press a key. If the problem persists, check that the batteries are fitted correctly. If necessary, replace them with 2 new 1. 5 V AAA/LR03 alkaline batteries. [. . . ]