User manual CAT EYE MSC 2DX
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CAT EYE MSC 2DX. We hope that this CAT EYE MSC 2DX user guide will be useful to you.
![]() |
Manual abstract: user guide CAT EYE MSC 2DX
Detailed instructions for use are in the User's Guide.
[. . . ] Just attach the 2Dx attachment on your bracket.
PUSH 2Dx attachment
2 3 4
Attaching Main Unit and Chest Belt Setting up Main Unit Other Important Features
E
2-8-25, Kuwazu, Hihashi Sumiyoshi-ku, Osaka 546-0041 Japan Service & Research Address for United States Consumers: CAT EYE Service & Research Center 1705 14 th St. 115 Boulder CO 80302 Phone: 303-443-4595 FAX: 303-473-0006 Toll Free: 800-5 CAT EYE URL: http://www. cateye. com
For more detailed setup and operations, please read the user manual.
-1-
1
Parts Installation
Parts Names
Make sure that the following parts are included in the package. 1 Bracket (Includes 2Dx attachment) 2 Speed Sensor 3 Sensor Band A (L/S) 4 Sensor Band B 5 Nylon Ties 6 Sensor Rubber Pad 7 Bracket Rubber Pad 8 Bracket Rubber Pad with Holder 9 Screw 0 Wheel Magnet
2Dx attachment
Important A B
2
marking line
0
The clearance between the sensor 2 and the magnet 0 should be about 5mm.
Align the center of the magnet 0 and the sensor's marking line while rotating the wheel.
Entire View
Magnet
Use a coin to attach the magnet 2 temporarily to the right side spoke of front wheel.
spoke
0
-2-
Speed Sensor
Attach the speed sensor temporarily to the right front fork. [. . . ] Wear the chest belt heart rate sensor in the legible way (the top mark on the transmitter should come to the top).
MainUnit
Mount:
1. Caution: When riding, do not touch the lever; the main unit might fall off.
PUSH Hook How to mount the unit to bicycle Release Lever Remove Release Lever
Remove:
To remove the main unit, unwind the wristband and push the lever. -4-
Input the wheel circumference of your bicycle into the main unit. Find out your bicycle's wheel circumference from the table below. If you cannot fine one, use the default figure " 2096" temporarily.
Name of Button The tire size is marked on the side of your tire.
3
Setting up Main Unit
(1) Initial Setting
!-1 Select a Speed Scale
wheel circumference
The main unit has 6 buttons: SET/AT button, MODE button, LAP button, LT button, S/S button and AC button. Push the MODE button to switch between "km/h" and "mph". Input your bicycle's wheel circumference obtained from the above table. (To increase/decrease rapidly, hold down the respective button. ) Caution: This is just the temporary setting of the wheel circumfer!-3
ence. When you want to change wheel circumference later, refer to "Changing wheel circumference" in page 13 of the user manual. Push SET/AT button to fix the setting, and the screen shows "Current Speed " in the upper display, "Heart Rate " in the middle display and "Elapsed Time TM" in the lower display (!Initial setting is completed.
"Elapsed Time TM"
!-4
-5-
(2) Basic Operations
Start and stop measurement Push S/S button and the unit will start measuring "Elapsed Time TM". At the same time, calculation of "Trip Distance DST" and "Average Speed AVS" starts. "Current Speed measured and displayed regardless of the start/stop. Switching Functions The upper display always shows "Current Speed ", and the middle display always shows "Heart Rate ". ", "Heart Rate ", "Total Distance ODO", "Maximum Heart Rate MXP" and "Maximum Speed MXS" continue to be
In the lower display, the selected function is displayed. The functions of the lower display are divided into the Main functions and Sub functions. You can not switch the Sub function to one another.
Hold Down (2sec. ) Just Push
Clock Time (Current Speed) Maximum Heart Rate Elapsed Time Average Speed
Maximum Speed
Trip Distance
Measurement screen map
Switching the lower display by pushing MODE button.
Total Distance
-6-
(3) Setting Clock Time
If you chose "km/h" for speed scale, clock time is in 24h mode; if you chose "mph", clock is in 12h mode.
#-1
1. Before entering into the clock setting mode, see that the bpm symbol in the middle display is not flashing. [. . . ] *When Auto function is on, just push S/S button and the upper display changes from "Current speed " to "Clock time ".
Reset Operation
To reset the data of "Elapsed Time TM", "Average Speed AVS", "Maximum Speed MXS", "Maximum Heart Rate MXP" and "Trip Distance DST", push S/S button and MODE button simultaneously.
Pace Arrow
When you are using the unit for cycling, the pace arrow appears in the right side of the lower display. The pace arrow indicates whether the current speed is higher or lower than the average speed. When the average speed is zero, no arrow appears.
Power Saving Feature
When the main unit is left without receiving any signal or there is no button operation for about 15 minutes, power is shut down and the unit will be in "sleep" state, displaying only clock. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CAT EYE MSC 2DX
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CAT EYE MSC 2DX will begin.