User manual CAT EYE CC-6000

[. . . ] PLEASE READ INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO INSTALL AND USE YOUR CAT EYE CORDLESS 7 COMPUTER. 1 Max. Distance 70 cm 1 Bracket 2 Sensor (Transmitter) Computer Set-up (for first use, or after replacing battery) 1 5 4 Nylon Ties (L x 2) Nylon Ties (S x 2) 3 2 Mounting View Press All-Clear button (AC). · Flashing "km/h" remains. AC Button SET button ST. /STOP button MODE button AC button 1 Secure bracket to handlebar with nylon ties (fig. Slide computer into mount until it snaps in place. 1 Slide 2 Click Adjust between "mph" or "km/h" by pressing the MODE button. Get your wheel circumference ! L mm km/h MODE (fig. [. . . ] Slide computer into mount until it snaps in place. 1 Slide 2 Click Adjust between "mph" or "km/h" by pressing the MODE button. Get your wheel circumference ! L mm km/h MODE (fig. A) 5 Lever mph Use the below table as the rough guide. L(mm) Tire Size 12 x1. 75 935 14 x 1. 50 1020 14 x 1. 75 1055 16 x 1. 50 1185 16 x 1. 75 1195 18 x 1. 50 1340 18 x 1. 75 1350 20 x 1. 75 1515 20 x 1-3/8 1615 22 x 1-3/8 1770 22 x 1-1/2 1785 24 x 1 1753 24 x 3/4Tubular 1785 24 x 1-1/8 1795 24 x 1-1/4 1905 24 x 1. 75 1890 24 x 2. 00 1925 24 x 2. 125 1965 26 x 7/8 1920 26 x 1(59) 1913 26 x 1(65) 1952 26 x 1. 25 1953 26 x 1-1/8 1970 26 x 1-3/8 2068 26 x 1-1/2 2100 26 x 1. 40 2005 26 x 1. 50 2010 26 x 1. 75 2023 26 x 1. 95 2050 26 x 2. 00 2055 26 x 2. 10 2068 26 x 2. 125 2070 26 x 2. 35 2083 26 x 3. 00 2170 27 x 1 2155 27 x 1-1/8 2161 27 x 1-1/4 2161 27 x 1-3/8 2169 650 x 35A 2090 650 x 38A 2125 650 x 38B 2105 700 x 18C 2070 700 x 19C 2080 700 x 20C 2086 700 x 23C 2096 700 x 25C 2105 700 x 28C 2136 700 x 30C 2170 700 x 32C 2155 700C Tubular 2130 700 x 35C 2168 700 x 38C 2180 700 x 40C 2200 The tire size is marked on both sides of the tire. 2 3 Mount the wheel magnet to a spoke on the front wheel (fig. B), so the magnet faces the sensor. 3 (fig. NOTE: The distance between the computer and the sensor must not exceed 70 cm--if the sensor is too far away from the computer head, the speed signal will not register on the computer. For best results, mount the sensor as high on the fork leg as reasonably possible, so that the sensor is within Front Fork transmission range to the computer. However, the sensor must be close enough to spokes to allow proper disSensor Screw 4 tance to magnet (see below). Front Fork Press the SET button to lock in your choice---OR--if you want to input previous mileage, hold the MODE button (before pressing the SET button) for 2 seconds. · Press the SET button when complete. SET MODE increase the figure MODE move to the next digit Sensor Base (fig. C) 2 Sensor Base ST. /STOP NOTE: When the wheel rotates, the magnet MUST line up with the mark on the sensor. ALSO NOTE: Magnet must pass within 5 mm of the sensor--if not, it will not trip the sensor as it passes, and the computer will not register speed. Adjusting the sensor position higher or lower on the fork leg or by rotating the sensor on the fork mount may be required to achieve proper distance to the wheel magnet. Less than 5mm SET 3 2 Magnet's center Marking line 3 2 Spin · · · · · · Wheel circumference number is shown. Press SET button when finished. increase the figure MODE 3 4 Test by spinning the front wheel. (Current speed does not appear. ) [If the sensor pulse indicator fails to flash, first spin front wheel to align computer with sensor. distance between sensor and unit is over 70cm. ] Is the clearance between the sensor and the magnet too large?Are the magnet's center and the sensor's marking line aligned?Adjust the sensor's position so that the distance becomes less than 70cm. Replace it with a new one and do all clear operation. Specification Battery ------------------------------ Computer: Lithium Battery CR2032 X 1 Sensor: Lithium Battery CR2032 X 1 Battery Life ------------------------- Computer: approx. 1 year (in the case of being used for 1 hour every day) Sensor: until Total Distance reaches about 10, 000km (6, 250mile) *This is the average figure of being used under 20°C temperature and the dis tance between the computer and the sensor is 65cm. Controller -------------------------- 4-bit 1-chip microcomputer (crystal controlled oscillator) Display ----------------------------- Liquid crystal display Sensor ------------------------------ No contact magnetic sensor Wheel Circumference Range ---- 10mm-2999mm (default figure: A: 2095mm, B: 2050mm) Working Temperature ------------ 0°C - 40°C (32°F - 104°F) Dimension/Weight ---------------- 1-19/32 x 2-7/32 x 27/32" (40 x 56. 5 x 21mm) / 1. 06oz (30g) * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. Limited Warranty 2-year warranty for computer/sensor only (excluding parts and batteries) If trouble or damage occurs during normal use, the product will be repaired or replaced free of charge. Type your name, address, date of purchase and the situation of trouble clearly on the warranty certificate, and send it back to the appropriate service center together with the product. Insurance, handling and transportation charges shall be borne by the customer. [. . . ] * The specifications and design are subject to change without notice. Limited Warranty 2-year warranty for computer/sensor only (excluding parts and batteries) If trouble or damage occurs during normal use, the product will be repaired or replaced free of charge. Type your name, address, date of purchase and the situation of trouble clearly on the warranty certificate, and send it back to the appropriate service center together with the product. Insurance, handling and transportation charges shall be borne by the customer. After being repaired or replaced, the product will be shipped back to the customer. [. . . ]