User manual CANDY PG640X

[. . . ] 3) Important - The diagram below shows how the sealant should be applied. 4 gas ­ PL03/PL04 - / yes -/1 1/1 2 1 1 8, 95 kW 649 g/h 3 230V/50Hz yes 590x510 mm. IE cat. II2H3 + A B The Hob unit is fitted by attaching the Fixing Clamps supplied, using the holes at the base of the unit. Fig. 1 C D accessible space This appliance has been designed for non-professional, i. e. 2 31 32 IE GB If the hob is fitted above an oven which is not equipped with fan cooling system it is recommended that openings are created within the built in furniture to ensure correct air circulation. [. . . ] If a plug is not already attached, fit a plug appropriate to the load indicated on the rating plate. Where the Hob is connected direct to the electricity supply, a circuit breaker must be fitted with at least a 3 mm contact spacing when in the open position. If the power supply cord is damaged this is to be replaced by a qualified engineer so as to prevent any potential risk. The earth wire ( green a yellow coloured) must be at least 10 mm longer than the live and neutral wires. The section of the cable used must be of the correct size in relation to the absorbed power of the hob. Please check rating plate for the power details and ensure that the power supply cord is of the TYPE H05V2V2F. To prevent any potential damage to the hob please carry out the installation following this sequence: GB IE 1/2 GAS CONICAL A) As illustrated, assemble parts in sequence: A) fixed pipe B) washer C) Elbow fitting with tapered thred connection 2) Tighten the joints with the Spanners, remembering to twist the pipes into position. 3) Attach fitting C to mains gas supply using rigid copper pipe or flexible steel pipe. MAINS SUPPLY LIVE EARTH L BROWN WIRE GREEN/YELLOW WIRE BLUE WIRE POWER CABLE NEUTRAL N Please note Some models are equipped with both conical and cylindrical connectors for gas supply. Please select the type which is correct for the supply concerned. Fig. 5 GAS CONNECTION These instructions are for Fitters qualified for installation of equipment in line with the relevant national standard. All work must be carried out with the electricity supply disconnected. The rating plate on the hob shows the type of gas with which it is designed to be used. It is possible to use other types of gas after carrying out some simple modifications. connection to the mains gas supply or gas cylinder should be carried out according to the relevant national standards, after having checked that it is regulated for the type of gas with which it will be supplied. If it is not correctly regulated follow the instructions in the paragraph entitlet «Adaption for different types of gas». For liquid gas (cylinder gas) use pressure regulators which comply with the relevant national standards. N. B. : for safe operation, economic use of energy and to ensure greater durability of the appliance, make sure that the supply pressure conforms with the values shown in the table on page 37. Use only pipes, washers and sealing washers which comply with the relevant national standards. When connecting the hob to the gas supply via use of flexible hoses please ensure that the maximum distance covered by the hose does not exceed 2 metres. N. B. : carry out a final check for leaks on the pipework using a soapy solution. Also, make sure that the flexible pipe cannot come into contact with a movlng part of the cabinet (eg, a drawer) and that it is not situated where it could be damaged. GB IE A Cylindrical (but connector) B Tapered thread conical ADAPTING THE HOB TO DIFFERENT TYPES OF GAS To adapt the Hob for use with different types of gas, carry out the following instructions: -- remove the grids and burners -- insert the hexagonal spanner (supplied) into the burner support (Fig. [. . . ] This is a normal and inevitable phenomenon, but it doesn't jeopardize absolutely the functionality of the hob. In anycase from our after sales service centre the spare parts are available. A neon indicator light adjacent to the control knob will glow when the electric plate is in use. The additional electric hotplate/ring (ø 80 mm) where featured is turned on and off by pressing 0/I button, this hotplate has a fixed heat setting. Only pans which have smooth flat bases should be used on the electric hotplates. [. . . ]