User manual CANDY CFT161-1

[. . . ] Standard daily cycle. 3in1(1pcs) Turning on the Appliance 1 2 3 4 5 6 7 Draw out the lower and upper basket, load the dishes and push them back. It is commended that loading the lower basket first, then the upper one. With a little force to ensure the door is properly closed. Press the Start/ to stop washing. button Note: a sound of perfectly. click could be heard when the door is closed Insert the plug into the socket. [. . . ] The power supply is 230V 50HZ, the specification of the socket is 250V 10A. Press the ON/OFF button According to the soil level to choose the desired program by pressing program selection button. 3 At end of washing, the time display will flash for 8 seconds while the buzzer sound. But at the end of delayed washing, no sound of the buzzer, only the flash of the time display. If your model have not water softener, you may skip this section. The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliances is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. 1 Remove the lower basket and then unscrew and remove the cap from the salt container. 2 3 4 If you are filling the container for the first time , fill water . Place the end of the funnel(supplied) into the hole and introduce about 1kg of salt . It is normal for a small amount of water to come out of the salt container Carefully screw the cap back on. 4 DETERGENT DISPENSER YOU MAY NOT ADD TOO MUCH DETERGENT TO PREVENT THE FORMATION OF DEPOSITS BECAUSE YOUR DISHWASHERS HAVE SPECIALLY-DESIGNED WATER SOFTENERS. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the" Wash Cycle Table". Your dishwashers use less detergent and rinse aid than conventional dishwashers. Generally, only one tablespoon of detergent is needed for a normal wash load. Always add the detergent just before starting dishwasher, otherwise it could get damp and will not dissolve properly. WARNING! Proper Use of Detergent In accorance with En50242 standard, the dispenser should be set on the maximum lever when doing the performance. 5 Loading the Dishwasher Racks. For best performance of the dishwasher, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model. It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the top spray arm. If the pressure is below the minimum consult our Service Department for advice. 1 2 3 Pull The supply hoses completely out from storage compartment located at rear of dishwasher. Tighter the screws of the safety supply hose to the faucet with thread 3/4inch. Turn water fully on before starting the dishwasher. WARNING! How to Disconnect the safety supply hose 1Turn off the water. the 2 Releasefromwater pressure by depressing the pressure release button. This relieves water pressure and protects you, and the room, severe splashing. 3 How to Disconnect the Dishwasher 1 Remove the power cord plug from the wall receptacle. 2 Disconnect Unicouple from faucet adapter. NOTE: When motor stops at the end of the final rinse, the Unicouple can be disconnected and returned to storage. 10 COLD WATER CONNECTION Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place. If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. HOT WATER CONNECTION The water supply to the appliance can also be connected to the house hot water line (centralized system, heating system), as long as it does not exceed a temperature of 60 C. In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Positioning the Appliance Position the appliance in the desired location. [. . . ] In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation. How to Drain Excess Water From Unicouple Hoses If the sink is 34 or higher from the floor, the excesswater in Unicouple hoses cannot be drained directly into the sink. [. . . ]