User manual CANDY CDI 5550 P

[. . . ] The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. "START" programme button "SALT EMPTY" light "RINSE AID EMPTY" light Programme guide "ON/OFF" button "PROGRAMME STATUS" lights For service and repairs call your local engineer on our national telephone number: Description of the control panel Technical data Programme selection and special functions The Waterblock system Water softener unit Programme guide EN 50242 place load Capacity with pans and dishes Water supply pressure Fuse Power input Supply voltage (Use in conjunction with programme guide) IMPORTANT The dishwasher has two very practical functions: - the "recommended" programme (which is ideal for full load daily use) for quick and accurate selection; - the "Auto' Memory", function saves any programme used at least 3 times consecutively, so that if you regularly use the same washing cycle you do not have to continually set the programme thereby saving time and effort. IMPORTANT All options MUST be turned on or off, BEFORE pressing "START" button. The dishwasher is equipped with a dirt sensor, able to analyse water murkiness during all "AUTOMATIC" programme phases (see programme list); thanks to this sensor the washing cycle parameters are automatically adapted to the real quantity of dirt on dishes. [. . . ] By using this option, the strength of the selected cycle will be increased, adding one rinse and increasing the temperature and water pressure in the washing phase where foreseen. This option is recommended for very dirty dishes or when dirty dishes may not have been pre-treated allowing the soiling to dry up. IMPORTANT With this option selected the "IMPULSE" wash is turned off. In response to your everyday washing requirement in addition to the normal wash functions this dishwasher is equipped with the "1/2 AUTO" function. This function enables the uses to wash a reduced number of dishes yet retaining the freedom of loading them both on the top and bottom basket. When this function is activated the dishwasher will automatically reduce the water and energy consumption and the wash time. If you open the door during the drying cycle, an audible audio signal advises you that the drying cycle has not yet finished. A 5 second buzzer will sound (if not muted) 3 times at 30 second intervals to signal that the programme has ended. Dishes can now be removed and the dishwasher turned off by pressing the "ON/OFF" button or dishes can be loaded for a new cycle. Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. proceed as follows to set a delayed start: Press the "DELAY START" button ("00" will appear on the display). Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). If you wish to see which programme has been selected, press the "PROGRAMME SELECTION" button. Proceed as follows to cancel a delayed start: Hold the "START" button down for at least 5 seconds. At this point, a new programme and option buttons must be set to start a new programme as indicated in the "PROGRAMME SETTINGS" section. The alarm for the programme end may be muted as follows: With the dishwasher off, hold down the "PROGRAMME SELECTION" button for few seconds while simultaneously pushing the "ON/OFF" button. To turn the alarm on again, follow the same procedure ("b1" will appear on the display to indicate that the buzzer is on). To ensure the correct operation of the anti-overflow safety device, we recommend that the dishwasher is not moved or tilted during operation. If however it is necessary to tilt or move the dishwasher, please ensure that the washing cycle is complete and that there is no remaining water inside the dishwasher. The waterblock system has been designed to improve the safety of your appliance, particularly when the machine is left unattended. The waterblock system actually prevents flooding which might be caused by a machine malfunction or as a result of a fracture on the pipes. How does waterblock work The sump located in the base of the appliance collects any possible water leakage and operates a sensor which subsequently activates a valve placed under the water tap and stops any water from the supply even with the tap fully opened. [. . . ] With cold water (15°C)** -Tolerance ± 10%Hot rinse with rinse aid Wash with prewash If setting the INTENSIVE wash programme, a second dose of about 20 g of detergent (1 table-spoon) must be added directly in the machine. ("RECOMMENDED" PROGRAMME) Once a day - for normal soiled pans and any other items that have been left all day for washing. Once a day - for heavily soiled pans and any other items that have been left all day for washing. Suitable for heavily soiled items that are to be washed straight after a meal (Max 8 place load). [. . . ]