User manual CANDY CBD 116 SY

[. . . ] Before opening the washing machine door, ensure that there is no water in the drum. Do not pull the mains lead Or the appliance itself to remove the plug from the socket. When the appliance location is on carpet floors, attention must be paid so as to ensure that there is no obstruction to the bottom vents. And/or incorrect operation, turn the washing machine off, close the water inlet tap and do not tamper with the appliance. [. . . ] When you are ready to unload, press the Crease Guard button ­ this will drain and spin ready for emptying If you do not want to spin the clothes and activate drain only: - release the START button - turn the selector knob to the OFF position - select programme drain - wait around 5 seconds - switch on the appliance again by pressing the START button EN SUPER RINSE BUTTON Thanks to the new electronic system, acting on the button is possible to effect a new special rinse cycle. The addition of a lot of more water and the new action combined of cycles of rotation of the drum with load and unloading of water, allow to get laundry perfectly rinsed. This function has been studied for the people with delicate and sensitive skin, for which also a least residue of detergent can cause irritations or allergies. It advises to also use this function for the children items and in case of washings of very dirty items, for which it is due to use a lot of detergent, or in the washing of towelling items whose fibers mostly have the tendency to hold the detergent. INTENSIVE WASH BUTTON This function which is available on all cotton programmes is very useful for heavy soiling. The temperature is kept constant throughout all the wash phases and the programme is extended to ensure an extra deep cleaning performance. This operation must be done before pressing the START button When setting very short delay times (1 or 2 hours) it is advisable to turn the knob to the last position (12 h) and then move it back to the required times. During the "Delay start" period, the indicators of the wash phase flash In case of power failure, the delay start function re-starts with the delay time at the same value just before the power failure. In the case where we wish to cancel the delay start, rotate the Delay Start knob to the " " position then press START. SPIN SPEED CONTROL ROTATES IN BOTH DIRECTIONS The spin cycle is very important to remove as much water as possible from the laundry without damaging the fabrics. By adjusting the control, it is possible to reduce the maximum speed, and if you wish, the spin cycle can be cancelled altogetherposition . The programme carries out with the programme selector stationary on the selected programme till cycle ends. Switch off the washing machine by pressing the START button and turning the selector to OFF. The detergent drawer is divided into 4 compartments: - The first I for the prewash detergent - The second II for the main wash detergent. For the various types of fabrics and various degrees of dirt the washing machine has 4 different programme bands according to: wash cycle, temperature and lenght of cycle (see table of washing cycle programmes). 1 Resistants Fabrics The programmes have been designed for a maximum wash and the rinses, with spin intervals, ensure perfect rinsing. 2 Mixed and Synthetic Fabrics The main wash and the rinse gives best results thanks to the rotation rhythms of the drum and to the water levels. 3 Special Delicate Fibres This is a new wash cycle which alternates washing and soaking and is particularly recommended for very delicate fabrics such as Pure Machine Washable Wool. The wash cycle and rinses are carried out with high water levels to ensure best results. This programme allows a complete washing cycle for garments specified as "Hand Wash only" on the fabric care label. The programme has a temperature of 30°C and concludes with 2 rinses and a slow spin. SPECIAL "RINSE" PROGRAMME The programme carries out three rinses with a spin at 800 rpm. [. . . ] Does not function on any programme CAUSE Mains plug not plugged in Mains switch not on No power Electric circuit fuses failure Load door open Insert plug Turn on mains switch Check Check Close load door Check Turn on water inlet tap Set timer on correct position Straighten discharge tube Check filter Replace washer and tighten the tube on the tap Wait a few minutes until the machine discharges water Turn the programme dial onto spin setting Adjust special feet Remove transport bracket Distribute the washing evenly See cause 1 Inlet tap turned off Timer not set correctly Discharge tube bent Odd material blocking filter Leak from the washer between the tap and inlet tube The washing machine has not discharged water "No spin" setting (some models only) Strong vibrations during spin Washing machine not perfectly level Transport bracket not removed Washing load not evenly distributed For prompt servicing, give the model of the washing machine, to be found on the label placed on the cabinet inside of the porthole or on the guarantee certificate. Important 1 The use of environment friendly detersives without phosphates may produce the following effects: - The discharge rinse water may result cloudier due to the presence of zeolites in suspension. - The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not remain incorporated in the fabric and does not alter the colour. [. . . ]