User manual BRAUN 370CC-3

[. . . ] Do not use this appliance with a damaged or broken foil, as serious skin injuries may occur. To disconnect, turn all controls to «off», then remove plug from outlet. When plugging to an electrical outlet outside the USA, use a plug adapter to match the outlet's pin configuration. 1 Foil & Cutter cassette 2 Long hair trimmer 3 Precision setting switch («lock») (390cc/370cc only) 4 On/off switch 5 Charging lights (green) 6 Low-charge light (red) 7 Cleaning light (yellow) 8 Replacement light for shaving parts (390cc/370cc only) 9 Shaver power socket 10 Special electric cord set 11 Travel pouch Charging lights The green charging lights (5) show the charge status of the batteries. [. . . ] However, do not clean the shaver Foil & Cutter cassette with a brush as this may damage it. Replacement light for shaving parts/Reset (390cc/370cc only) To maintain 100% shaving performance, replace the shaver Foil & Cutter cassette (1), when the replacement light for shaving parts (8) comes on (after about 18 months) or when worn. The replacement light will remind you during the next 7 shaves to replace the foil and cutter cassette. After you have replaced the Foil & Cutter cassette (1), press the on/off switch (4) for at least 5 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete. Model 350cc: To maintain 100% shaving performance, replace the shaver Foil & Cutter cassette (1) at least every 18 months or when worn. Preserving the batteries In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (by shaving) every 6 months approximately. To protect the environment, do not dispose of the appliance in the household waste at the end of its useful life. During the automated cleaning process, the shaver is switched on and off at intervals to obtain best cleaning results. Small amount of oil, the cleaning procedure also fulfils the lubrication needs of the shaver. important · Only use the power supply special electric cord set supplied with the shaver. ⷠIn order to avoid any leakage of the cleaning fluid, place the appliance on a flat, stable surface. Do not tip, move suddenly or transport in any way if a cleaning cartridge is installed. ⷠDo not place the appliance in a mirror cabinet, nor store it over radiators, nor place it on polished or lacquered surfaces. Connect your Clean&RenewTM with the cord set to the mains electricity supply. After each shave, switch the shaver off and put it into the Clean&RenewTM, upside down and with the front showing. ⷠPush the start/release button (1) to lock and connect the shaver. The yellow light on the shaver will flash during the complete process (approx. Do not interrupt the cleaning process, as it leaves the shaver wet and not fit for use. When cleaning is finished, the yellow light will go off and the shaver is ready for use. ⷠA cleaning cartridge should be sufficient for about 30 cleaning cycles. When the level indicator (4) has reached the «min» mark, the remaining fluid in the cartridge is sufficient for about 5 more cleaning cycles. [. . . ] 2 year limited warranty (foil and cutter block excluded) Braun warrants this Braun shaver (except foil and cutter block) to be free of defects in material and workmanship for a period of two years from the date of original purchase. If the shaver exhibits such a defect, Braun will, at its option, either repair or replace it for the consumer without charge. please call 1-800-Braun 11 (800-272-8611) to be referred to the authorized Braun Service Center closest to you. This warranty does not cover foil and cutter cassette or damage resulting from accident, misuse, abuse, dirt, water, tampering, unreasonable use, normal wear, servicing performed or attempted by unauthorized service agencies or failure to provide reasonable and necessary maintenance, including recharging. [. . . ]