User manual BOSCH SMI 63M56EU/81 SUPPLEMENT

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSCH SMI 63M56EU/81. We hope that this BOSCH SMI 63M56EU/81 user guide will be useful to you.


BOSCH SMI 63M56EU/81 SUPPLEMENT: Download the complete user guide (740 Ko)

Manual abstract: user guide BOSCH SMI 63M56EU/81SUPPLEMENT

Detailed instructions for use are in the User's Guide.

[. . . ] SAVE THIS MANUAL Use the plastic bag and tie provided, to hang manuals nearby the softener for future reference. · Warranty · Installation · Start Up / Setting Timer · How It Works · Care Of · Specifications · Repair Parts Systems Tested and Certified by NSF International against NSF/ANSI Standard 44 for softener performance. Sears, Roebuck and Co. , 3333 Beverly Road, Hoffman Estates, IL 60179 USA PRINTED IN U. S. A. www. KenmoreWater. com Part No. E 12/8/06) WARRANTY ON WATER SOFTENER ONE YEAR LIMITED WARRANTY ON WATER SOFTENER When installed, operated and maintained according to all instructions supplied with the product, if this Kenmore appliance fails due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair. THREE YEAR LIMITED WARRANTY ON ELECTRONIC PARTS When installed, operated and maintained according to all instructions supplied with the product, if any of the following electronic parts fail due to a defect in material or workmanship, call 1-800-4-MY-HOME® to arrange for free part replacement: Brine Tank Light, Electronic Board, Sensor Housing, Wiring Harness, Transformer, Micro Switch, Drive Motor, Power Cable. TEN YEAR LIMITED WARRANTY AGAINST LEAKS When installed, operated and maintained according to all instructions supplied with the product, if the water softener tank or salt storage drum develops a leak within ten years from the date of purchase, call 1-800-4MY-HOME® to arrange for free tank or drum replacement. [. . . ] 33 SALT SIGNAL LEVEL LEVEL RECHARGE NOW Press the REGENERATION button and hold until *RECHARGE, Serv and Fill begin to flash in the display. Upon reaching fill, the first cycle of regeneration, the flashing Serv goes off and Fill is on steady. * NOTE: If the CLEAN feature is set to ON, a cleaning backwash (CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining) precedes the recharge. 8 7 6 5 4 3 2 1 PM RECHARGE TONIGHT FIG. 34 Indicator Light Bars, Salt Level SALT SIGNAL LEVEL LEVEL SALT LEVEL Brinewell RECHARGE TONIGHT Press and release (do not hold) the REGENERATION button. RECHARGE TONIGHT flashes in the display, and the softener begins regeneration at the next preset recharge time. Press and release the REGENERATION button once more if you decide to cancel the regeneration, and RECHARGE TONIGHT will not flash in the display. Decal Salt Level 8 7 6 5 4 3 2 1 FIG. 35 SALT MONITOR SYSTEM The face plate timer has a low salt monitor with an indicator light to remind you to add salt to the storage tank. The salt level decal, on the brinewell inside the tank, has numbers from 0 to 8 (see drawing below). Now, press the RESET SALT LEVEL button until black bars display up to the salt level number. Finally, set the level you want the low salt indicator light to come on. Press the SET LOW SALT LIGHT button until a (*) shows opposite this number. When this feature is ON, the softener will automatically recharge when 97% capacity has been used, at any time of day. 12 or 24 hour clock: All time displays are shown in standard clock time (1 to 12 PM; and 1 to 12 AM) at the 12 hr default setting. If Military time displays are desired, set to 24 hr by pressing the UP button. Gallon or Liter readings: Water usage and flow displays are shown in gallons. If you prefer to have the same displays in liters, press the UP button until Liter shows. Maximum days between regenerstions: The faceplate timer automatically controls regeneration frequency (see page 28). This provides the greatest operating efficiency, and under most conditions, this feature will be left in its default mode. However, modify this feature if you want to force a regeneration every set number of days. For example, if your water supply contains iron and you want the softener to regenerate at least once every few days to keep the resin bed clean, set the display as typically shown above. Setting is available from 1 to 15 days by using the UP and DOWN buttons. Press SELECT 1 to return the present time display. SALT SIGNAL LEVEL LEVEL SALT SIGNAL LEVEL LEVEL SALT SIGNAL LEVEL LEVEL SALT SIGNAL LEVEL LEVEL 8 7 6 5 4 3 2 1 RECHARGE 8 7 6 5 4 3 2 1 RECHARGE FIG. [. . . ] The electronic timer again energizes the motor to return the valve to service. As the valve rotates, the position switch lever drops to open the circuit. The valve remains positioned in service until the electronic timer initiates the next regeneration. Soft Water To Valve Outlet Drain Position Switch FIG. Call The Kenmore Water Line 1-800-426-9345 41 Exploded View Kenmore MODEL Nos. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSCH SMI 63M56EU/81




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSCH SMI 63M56EU/81 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.