User manual BOSCH MUM6UC

[. . . ] Owner's Manual Universal Series Kitchen Machines for models: MUM 6610 UC · MUM 6622 UC MUM 6630 UC READ THIS MANUAL thoroughly for important safety and operating instructions before using this appliance. 1 IMPORTANT SAFEGUARDS WARNING: A risk of fire and electrical shock exists in all electrical appliances and may cause personal injury or death. When using electrical appliances, basic safety precautions should always be followed, including the following: 1. To protect against risk of electric shock, do not put the drive unit in or under water or other liquid. Close supervision is necessary when any appliance is used near children. [. . . ] When using the mixing bowl to knead or mix a recipe designed to be prepared by hand, you will find that with the Bosch Kitchen Machine you can usually place all the ingredients in the mixing bowl at once. If a large batch of dough is to be left in the mixing bowl and allowed to rise, the cover and splash ring should be removed and placed loosely on the bowl so that it is free to move if the dough should begin to press on it. 13 3. Place and engage the twin beating whisk assembly on the driveshaft of the mixing bowl as shown in figure 6. Figure 6. 4. Place the splash ring on the cover, making sure the tabs on the bowl fit into the recesses in the splash ring, and turn counterclockwise, see figure 5a. Then place the cover on the splash ring so that the tabs on the splash ring fit into the recesses in the bowl cover and turn the cover counterclockwise to fasten the bowl cover to the bowl. See figure 5b. Removing Contents Before beginning to remove the contents from the mixing bowl, make sure that the power unit has been turned to the Off position, "O/Off. " Remove the cover and splash ring by turning clockwise and lifting off. Once the cover and splash ring have been removed, the dough hook or the twin beating whisks may be removed by turning the hook or whisk assembly clockwise while lifting. The mixing bowl can be removed from the power unit by turning the bowl clockwise while lifting. Care and Cleaning of Bowl and Its Accessories Except for the whisk holder and the dough hook, the mixing bowl and its accessories are dishwasher safe. It is recommended that the whisk holder and the dough hook be washed by hand in warm soapy water, rinsed well and dried after each use. The whisks can be removed from the whisk holder by simply pulling them off, see figure 7a. Blender with Unbreakable Plastic Jar (MUZ 7 MX1) WARNING 1. There is a risk of injury from sharp blades when using the blender attachment. Keep hands and utensils out of the blender jar while it is attached to the power unit. To avoid injury, never place blade assembly on power unit without blender jar properly attached. Always hold cover in place while operating the blender to prevent cover from coming loose. The use of attachments, including canning jars, not recommended by the manufacturer, may cause a risk of personal injury. When blending hot and/or frothing liquids, process a maximum of 18 fluid ounces (0. 5 litres) at a time. Figure 7. After washing, rinsing and drying, the whisks may be placed back on the whisk holder by reversing the action to remove them, see figure 7b. The power unit of the kitchen machine should be cleaned using a clean, damp cloth only. Never use coarse or caustic cleaning products to clean this appliance. 8e. Cover closure/funnel Cover Blender jar Gasket Blade/base assembly The MUM 6622 UC Bosch Universal Series Kitchen Machine includes the MUZ 6 MX2 blender accessory. How to Use Blender The blender has been designed for crushing ice; mixing liquids; pureeing vegetables; preparing special diet and infant foods; pulverizing fruit, vegetables, nuts and dried bread (for bread crumbs); and preparing mayonnaise and sauces. Before beginning to use this or any other attachment, make sure that the power unit is on a clean, smooth, suitable work surface and switched to off position, "O/Off, " and that you have removed the motor drive cover. [. . . ] > Wait a few minutes (minimum 30 minutes recommended) to allow the motor to cool. > Depress the manual reset button on the bottom of the power unit, see figure 2b. > Reinstall the attachment and resume use per attachment's instructions. > Turn the power unit to the Off position, "O/Off, " and unplug. [. . . ]