User manual BOSCH MKM6000

[. . . ] The sole plate turns • This may occur after prolonged • Clean the sole plate regularly brown. The appliance • Water is being pumped into the • This is normal. not use the steam generator and contact an authorised technical service centre. Loss of pressure • Steam release button has been • Use the steam release button during ironing pressed for a long period of time. [. . . ] It has a large detachable water tank that can be refilled at any time without switching off the system. We hope that you enjoy ironing with this steam station. Important Please read these instructions for use carefully before using the appliance and save them for future reference. This appliance has been designed exclusively for domestic use and must not be used for industrial purposes. Warning: ¡The housing of the steam generator can get very hot ! General safety instructions • Before plugging the appliance into the mains, check that the voltage corresponds to that stated on the rating plate found on the base of the steam generator. We do not recommend the use of an extension cable, however if you need to use one, please ensure that it is suitable for its use with this appliance. If using an extension cable, make sure that it has a 16 A bipolar socket with an earth connection. • This appliance must only be used for the purposes for which it was designed, i. e. The manufacturer will not be held responsible for any damage arising from misuse or improper use. • The electrical plug must not be removed from the socket by tugging on the cable. • Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc. ). • With the aim of avoiding dangerous situations, any work of repair that the appliance may need, e. g. replacing a faulty mains cable, must only be carried out by qualified personel from an AuthorizedTechnical Service Centre. • Never immerse the iron or steam tank in water or any other liquid. Use of the soleplate cover also does away with the need for a cloth to prevent shine on dark materials. It is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the soleplate cover to the iron, place the tip of the iron into the end of the soleplate cover and pull the elastic strap over the lower rear of the iron until it fits tightly. To release the soleplate cover, pull the elastic strap and remove the iron. The fabric-protection soleplate cover may be purchased from Aftersales or the Bosch eShop: Accessory code (After-sales) 464846 Name of accessory (Bosch eShop) TDZ2510 Ironing without steam 1. Begin ironing but without pressing the steam release button (15). Vertical steam 1. Set the temperature dial (13) to the ”•••” or ”max” position. 2. You can steam iron curtains and hanging garments (jackets, suits, coats. . . ) by placing the iron in a vertical position and pressing the steam release button (15). 8. This appliance has a built-in water level sensor. The “water empty” indicator (8) will light when the water tank is empty. Note: The water tank (1) can be filled at any time while using the appliance. 9. If ironing with steam, adjust the steam control (3), (see: ironing with steam) Intelligent steam This system has intelligent steam control, which, after releasing the steam release button (15), provides a small amount of additional steam. The additional steam can always be stopped by briefly pressing the steam release button once again. Important: • Normal tap water can be used. To prolong the optimum steam function, tap water may be mixed with distilled water 1:1. [. . . ] 4. Never use abrasive products or solvents. “Energy saving” button If the ”Energy saving” button (4) is switched on, you can save up to 25% of the energy consumption and still have a good ironing result for most of your garments. It is advisable to use the normal energy setting only for thick and highly wrinkled fabrics. Automatic clean warning Pilot light (8) will flash indicating that boiler must be rinsed. To do this, follow the procedure described in the “Calc‘nclean” section above. To reset the “Calc‘nclean” pilot light and counter, switch the station off and on again twice, for a duration of at least 30 seconds each time Calc‘n clean Cleaning the Boiler To extend the life of your steam generator and to avoid any build up of scale, it is essential that you rinse out the boiler after several hours of use. [. . . ]