User manual BLACK & DECKER KS801SEKA

[. . . ] The correct power tool will do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. [. . . ] When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. Labels on tool The following symbols are shown on the tool: : Warning!To reduce the risk of injury, the user must read the instruction manual. 5 ENGLISH Electrical safety (Original instructions) # Use Adjusting the shoe plate for bevel cuts (fig. The shoe plate (4) can be set to a left or right bevel angle of 22. 5° or 45°. u Pull the shoe (4) forward, rotate the shoe to the left or right and push it back into the 22. 5° or 45° location. To reset the shoe plate (4) for 90° cuts: u Loosen the screw (10). u Pull the shoe (4) forward, rotate to the centre and push it back into the 0° location. u Tighten the screw. This tool is double insulated; therefore no earth wire is required. Always check that the power supply voltage corresponds to the voltage on the rating plate. u If the supply cord is damaged, it must be replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard. Features This tool includes some or all of the following features. 1. Variable speed switch (KS901PE) or On/Off switch (KS801SE and KS901SE) 2. Lock-on button 3. Saw blade locking lever 4. Shoe plate 5. Dust extraction outlet 6. Pendulum stroke / AutoSelect dial Variable speed control u Assembly Warning!Before attempting any of the following operations, make sure that the tool is switched off and unplugged and that the saw blade has stopped. Used saw blades may be hot. Use a high speed for wood, medium speed for aluminium and PVC and low speed for metals other than aluminium. Switching on and off u Fitting the saw blade (fig. A) u Hold the saw blade (7) as shown, with the teeth facing forward. u Insert the shank of the saw blade into the blade holder (8) as far as it will go. Slide the vacuum nozzle into the dust extration outlet (5). To switch the tool on, press the variable speed switch (1). u For continuous operation, press the lock-on button (2) and press the variable speed switch. To switch the tool off, when in continuous operation, press the variable speed switch once more and release it. Connecting a vacuum cleaner to the tool (fig. D) u u Residual risks Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include: u Injuries caused by touching any rotating/moving parts. When using any tool for prolonged periods ensure you take regular breaks. u Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF. ) 6 Use a pencil to mark the cutting line. Viewing from directly above the jig saw, the line of cut can be followed easily. Cutting mode Pendulum stroke or action provides a more aggressive blade motion and is designed for cutting soft materials such as wood or plastic. [. . . ] This guarantee statement is in addition to and in no way prejudices your contractual rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area. If your Black & Decker product becomes defective due to faulty materials or workmanship within 24 months from the date of purchase, Black & Decker guarantees to replace all defective parts, repair products subjected to fair wear and tear or replace such products to make sure of the minimum inconvienience to the customer unless: u The product has been used for trade, professional or hire purposes. u The product has sustained damage through foreign objects, substances or accidents. [. . . ]