User manual BLACK & DECKER HP146F2K

[. . . ] HP126F2K HP146F2K HP148F2K HP188F2K 1 Copyright Black & Decker 2 5 6 4 3 2 1 10 8 7 9 14 13 11 13 12 A 3 10 9 17 15 16 B C 19 4 18 19 20 21 D 4 14 13 13 12 9 11 9 E F 23 22 2 G H 5 5 3 24 I J 6 ENGLISH CORDLESS DRILL/SCREWDRIVER HP126F2K/HP146F2K/HP148F2K/HP188F2K CONGRATULATIONS!EC DECLARATION OF CONFORMITY HP126F2K/HP146F2K/HP148F2K/HP188F2K Black & Decker declares that these tools conform to: 98/37/EC, 89/336/EEC, 73/23/EEC, EN 50260, EN 55014, EN 60335, EN 61000 Level of sound pressure, measured according to EN 50260: HP126F2K LpA (sound pressure) LWA (acoustic power) dB(A) dB(A) 74 87 HP148F2K LpA (sound pressure) LWA (acoustic power) dB(A) dB(A) 81 94 HP146F2K 69 82 HP188F2K 76 89 INTENDED USE Your Black & Decker drill/screwdriver HP126F2/ HP146F2 has been designed for screwdriving applications and for drilling in wood, metal and plastics. Your Black & Decker drill/screwdriver HP148F2/ HP188F2 has been designed for screwdriving applications and for drilling in wood, metal, plastics and soft masonry. Your Black & Decker charger has been designed for charging Black & Decker batteries of the type supplied with this tool. [. . . ] Slide the battery into the receptacle and push until the battery snaps into place. x To remove the battery, push the release button (10) while at the same time pulling the battery out of the receptacle. A & C) This tool is fitted with a keyless chuck to allow for an easy exchange of bits. x Lock the tool by setting the forward/reverse slider (2) to the centre position (fig. x Open the chuck by turning the front part (15) with one hand while holding the rear part (16) with the other (fig. x Firmly tighten the chuck by turning the front part (15) with one hand while holding the rear part (16) with the other. This tool is supplied with a double-ended screwdriver bit in the bit holder (7) (fig. x To remove the screwdriver bit from the bit holder, lift the bit from the recess. When your project entails both drilling and screwdriving, fit a screwriver bit in the spindle and a drill bit in the chuck: you will then only need to remove the chuck for screwdriving and refit it for drilling. You can also fit drill bits with a hexagonal shaft in this way. Never use a light socket. A) Variable speed switch Forward/reverse slider Mode selector / torque adjustment collar Chuck Two-gear selector Battery charge indicator (HP148F2/HP188F2) Bit holder Side handle (HP188F2) 1. 8. 10 ENGLISH x x x To remove the chuck (4), keep the release tabs (18) depressed and pull the chuck off the spindle (19). Install a screwdriver bit (20) by pushing it into the spindle (19) as shown. To remove the screwdriver bit, pull the ring (21) back and pull the screwdriver bit out of the spindle. To refit the chuck, push it onto the spindle until it is firmly locked into place. Always make sure that the chuck is securely fitted. HP188F2 - Fitting the side handle (fig. x Tighten the side handle by turning it clockwise. USE Let the tool work at its own pace. Do not overload. To charge the battery (9), remove it from the tool and insert it into the charger (11). If the green end of charge indicator (14) lights up now instead, the battery is too hot and cannot be charged. If this happens, remove the battery from the charger, let the battery cool down for approx. 1 hour of charging, the red charging indicator (13) will stop lighting and the green end of charge indicator (14) will light up. J) x For drilling in steel and for screwdriving applications, slide the two-gear selector (5) towards the front of the tool (1st gear). [. . . ] Collected batteries will be recycled or disposed of properly. Technical data Voltage No-load speed Max. drilling capacity in steel/wood/masonry Weight (without battery) Battery Voltage Capacity Weight Charger Input voltage Approx. charging time VDC min-1 Nm mm mm kg HP126F2K 12 0-400/0-1, 200 20. 2 10 10/25 1. 3 A12 12 1. 2 0. 52 A12F 12 1. 5 0. 6 HP146F2K 14. 4 0-300/0-1, 100 22. 1 10 10/30 1. 3 A14 14. 4 1. 2 0. 65 HP148F2K 14. 4 0-300/0-1, 100 22. 1 10 10/30/12 1. 3 A18 18 1. 2 0. 76 HP188F2K 18 0-500/0-1, 600 29. 4 10 10/35/15 1. 4 A18F 18 1. 5 0. 9 VDC Ah kg A14F 14. 4 1. 5 0. 76 VAC min F2C models 230 15 F2K/F2B models 230 60 13 ENGLISH GUARANTEE (UK, SOUTH AFRICA, AUSTRALIA AND NEW ZEALAND ONLY) Should your Black & Decker product become defective due to faulty materials or workmanship, within 24 months from the date of purchase, we guarantee to either replace all defective parts or -at our discretion- to replace the unit free of charge, provided that: x The product is returned to us or one of our authorised repair agents with proof of purchase. x The product has not been used for trade, professional or hire purposes. [. . . ]