User manual BLACK & DECKER HP126FSC

[. . . ] Dress properly Do not wear loose clothing or jewellery, as these can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Use a face or dust mask whenever the operations may produce dust or flying particles. Connect dust extraction equipment If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used. [. . . ] A) Variable speed switch Forward/reverse slider Mode selector / torque adjustment collar Chuck Two-gear selector Battery charge indicator (HP128F2/HP148F2/HP188F2) 7. & Ireland only) N N N N N N N Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorised repair agent or a qualified electrician. Disconnect the plug from the supply and remove the fuse from the plug. Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. Only fit 13 Amperes BS1363A approved plugs fitted with a 5 A fuse (1). The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the leads are correctly fixed at the terminal screws. If the plug has a fuse cover, make sure that the fuse cover is fitted. Do not use the plug if the fuse cover is missing or damaged. Fitting and removing the battery (fig. B) N To fit the battery (9), line it up with the receptacle on the tool. Slide the battery into the receptacle and push until the battery snaps into place. N To remove the battery, push the release button (10) while at the same time pulling the battery out of the receptacle. A & C) This tool is fitted with a keyless chuck to allow for an easy exchange of bits. N Lock the tool by setting the forward/reverse slider (2) to the centre position (fig. N Open the chuck by turning the front part (15) with one hand while holding the rear part (16) with the other (fig. N Firmly tighten the chuck by turning the front part (15) with one hand while holding the rear part (16) with the other. This tool is supplied with a double-ended screwdriver bit in the bit holder (7) (fig. N To remove the screwdriver bit from the bit holder, lift the bit from the recess. N To store the screwdriver bit, firmly push it into the holder. Never use a light socket. 10 ENGLISH HP126F2/HP146F2 - Removing and fitting the chuck (fig. When your project entails both drilling and screwdriving, fit a screwriver bit in the spindle and a drill bit in the chuck: you will then only need to remove the chuck for screwdriving and refit it for drilling. N To remove the chuck (4), keep the release tabs (18) depressed and pull the chuck off the spindle (19). [. . . ] The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area. If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 48 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless: Technical data Voltage No-load speed Max. Capacity Weight (without battery) VDC min-1 Nm mm mm HP126FSC 12 0-400/0-1, 200 20. 2 10 10/25/A12F Ah 1. 5 kg 1. 3 HP146F2K 14. 4 0-300/0-1, 100 22. 1 10 10/30/A1714 Ah 1. 7 kg 1. 3 HP126F2K 12 0-400/0-1, 200 20. 2 10 10/25/A1712 1. 7 1. 3 HP148F2K 14. 4 0-300/0-1, 100 22. 1 13 13/30/12 A1714 1. 7 1. 4 HP128F2K 12 0-400/0-1, 200 20. 2 10 10/25/12 A1712 1. 7 1. 2 HP188F2K 18 0-500/0-1, 600 29. 4 13 13/35/15 A1718 1. 7 1. 4 Voltage No-load speed Max. charging time VDC min-1 Nm mm mm VAC 230 hr 1 13 ENGLISH N N N N The product has been used for trade, professional or hire purposes; The product has been subjected to misuse or neglect; The product has sustained damage through foreign objects, substances or accidents; Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff. To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. [. . . ]