User manual BLACK & DECKER GT4550

[. . . ] The correct power tool will do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. [. . . ] u Do not put the tool down until the blades have come to a complete standstill. Should you accidentally hit any such object, immediately switch the tool off and check for any damage. u Should the tool start to vibrate abnormally, immediately switch it off and disconnect it from the mains suply then check for any damage. Disconnect it from the mains supply before attempting to remove any obstructions. Never attempt to use an incomplete tool or a tool with unauthorised modifications. u Be aware of falling debris when cutting the higher sides of a hedge. u Always hold the tool with both hands and by the handles provided. Safety of others u This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. u Children should be supervised to ensure that they do not play with the appliance. Residual risks. Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include: u Injuries caused by touching any rotating/moving parts. When using any tool for prolonged periods ensure you take regular breaks. 5 ENGLISH u (Original instructions) Electrical safety Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF. ) Vibration # The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. u When using the tool outdoors, only use extension cables intended for outdoor use. A suitable rated Black & Decker extension cable of up to 30 m can be used without loss of power. u Electric safety can be further improved by using a highsensitivity 30 mA residual current device (RCD). u Features This tool includes some or all of the following features. 1. Trigger switch 2. Front handle switch 3. Front handle 4. Guard 5. Blade 6. Cable restraint Labels on tool The following pictograms are shown on the tool: : Assembly O E Warning!To reduce the risk of injury, the user must read the instruction manual. Warning!Before assembly, make sure that the tool is switched off and unplugged and that the blade sheath is fitted over the blades. Fitting the guard (fig. [. . . ] To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at: www. 2helpU. com Please visit our website www. blackanddecker. co. uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www. blackanddecker. co. uk % GT4245 / GT4550 Black & Decker declares that these products described under "technical data" are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-15 2000/14/EC, Hedge trimmer 1960 min-1, Annex V Measured sound power (LpA) 93 dB(A) Uncertainty (K) 3 dB(A) Guaranteed sound power (LpA) 96 dB(A) Uncertainty (K) 3 dB(A) These products also comply with directive 2004/108/EC and 2011/65/EU. [. . . ]