User manual BERNINA 1011

[. . . ] The copyright of this manual is reserved by Samsung Electronics, Co. , Ltd. The contents of this manual may not be partially or in whole reproduced, distributed or used in any form without the written permission of Samsung Electronics, Co. , Ltd. The BERNINA logo and SyncMaster are the registered trademarks of Samsung Electronics, Co. , Ltd. Microsoft, Windows and Windows NT are the registered trademarks of Microsoft Corporation. [. . . ] · <Dynamic Contrast> Controls the picture contrast automatically so that bright and dark pictures are balanced overall. This menu is unavailable when < Angle> or <Eco Saving> is set. Using the product 3-19 Menu Description This feature allows you to see optimal screen quality according to your viewing position. When viewing the screen at an angle from below, above or the side of the monitor, by setting the appropriate mode for each position you can obtain a similar picture quality as viewing the screen directly from the front. · · · · · · <Off> - Select when viewing from the front position. -Select when viewing from the upper position. <Lean Back Mode1> <Lean Back Mode2> <Standing Mode> <Side Mode> - Select when viewing from the left or right position. , , position at the same <Group View> - Select when two or more persons view among time. Angle · <Custom> -When <Custom> is selected, settings for <Lean Back Mode 1> is applied by default. Users can set suitable picture quality as needed. · · This menu is unavailable when < mode. This menu is unavailable when < Bright> is set to <Dynamic Contrast> or <Cinema> Color> is set. Removes vertical noise lines (line pattern) from the screen. Coarse The location of the screen may be changed after the adjustment. In this case, move the screen so that the screen is displayed at the center of the display panel using the <H-Position> menu. Fine If you cannot remove the noise completely with the <Fine> function, adjust the <Coarse> and then use the <Fine> function again. This can only be set when the external input is connected through DVI and <PC/AV Mode> is set to <AV>. · · · <4 : 3> - Displays pictures at the 4:3 aspect ratio. <Screen Fit> - If a 720P, 1080i or 1080P signal is input in DVI input mode, the picture is displayed as is without truncation. · · Menu H-Position Menu V-Position It can only be selected if an external input is connected to the DVI terminal and the <PC/AV Mode> is set to <AV>. When the panel is of 16:10, the screen size options include <4:3>, <wide>, <Screen fit>. You can adjust the horizontal position of the OSD. You can adjust the vertical position of the OSD. 3-19 Using the product SETUP&RESET Menu Reset Description Use this function to restore the visual quality and color settings to the factory defaults. · <No> - <Yes> Select a language for the OSD. Language The selected language is only applied to the product OSD. This function provides user a low power mode which is realized by lowering the current of the display panel. · · · <75%> When <75%> is selected, the power consumption is about 75% of default setting. <50%> When <50%> is selected, the power consumption is about 50% of default setting. <Off> When <Off> is selected, the function is turned Off . [. . . ] Use the software utility installed on your computer to set up this feature. STATE Power Indicator Power Consumption NORMAL OPERATION On 34 watts POWER SAVING MODE Blinking Typical 0. 3 watts POWER OFF Off Typical 0. 3 watts If there is no power cut-off switch, the power consumption is "0" only when the power cord is disconnected. More Information 6-26 6-27 Specifications MODEL NAME Size Panel Display area Pixel Pitch Synchronization Display Color Resolution Optimum resolution Maximum resolution Horizontal Vertical 24 inches (61 cm) 531. 36 mm (H) x 298. 89 mm (V) 0. 27675 mm (H) x 0. 27675 mm (V) 30 ~ 81 kHz 56 ~ 75 Hz 16. 7 M 1920x1080 @60 Hz 1920x1080 @60 Hz RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB Input Signal, Terminated 0. 7 Vp-p ± 5% separate H/V sync, Composite, SOG TTL level (V high 2. 0V, V low 0. 8V) Audio input : 1pin , PC audio signal input Audio signal Audio output : 1pin , earphone connector Speaker : 1Watt x 2 USB Hub USB up x 1 , USB 2. 0 down x 2 149MHz (Analog, Digital) This product supports 100-240 V. Since the standard voltage may differ from country to country, please check the label on the back of the product. 15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable 570 x 347 x 50 mm (22. 0 x 14. 7 x 2. 0 inches) (Without Stand) 570 x 387 x 201 mm (22. 4 x 15. 2 x 7. 9 inches) (With Stand) / 5. 2 kg (11. 5 lbs) 100 mm x 100 mm / 100 mm x 200 mm Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity :10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 140°F (-20°C ~ 60°C) Humidity : 5 % ~ 95 %, non-condensing -3°( ±2°) ~25° ( ±2°) S24A450S Maximum Pixel Clock Power Supply Signal Cable Dimensions (WxHxD) / Weight VESA Mounting Interface Environmental considerations Tilt Operating Storage Design and specifications are subject to change without prior notice. Class B (Information Communication equipment for residential use) This device is registered for EMC requirements for home use (Class B). [. . . ]